GE WSXH208T Скачать руководство пользователя страница 17

Страница: 17 / 51

CONSTRUCTION AND OPERATION

CONSTRUCTION

The front loading, tumble action clothes washer con-

sists of a perforated, cylindrical tub suspended

horizontally on its axis within a larger solid cylindrical

tub. This assembly is suspended by springs within a

four piece steel cabinet. A see through door and a

flexible bellows (seal) provides access for loading and

unloading clothes. The control console configuration

provides the versatility of stacked or undercounter

installations.

The washer is shipped with a painted top panel, but a

galvanized panel is available if the washer is to be

installed undercounter.

CONSOLE

The controls are mounted on the front of the cabinet and

are accessible for service by removing the washer top

service panel. On stacked installations, the dryer must

be removed from the washer.

CABINET

The cabinet is made of heavy steel in a four piece

design with an enamel finish. The sides and front are

riveted at the front corners and base. The rear of the

cabinet is galvanized steel and is secured with screws.

FRONT PANEL AND DOOR ASSEMBLY

The front panel is riveted to the side panels for maxi-

mum strength and structural rigidity.

BELLOWS

The bellows is a rubber sleeve that seals the sus-

pended outer tub to the stationary cabinet front at the

tub opening. Its purpose is to provide a water tight

opening into the tub that can be sealed by the cabinet

door, yet allow flexibility for the oscillation of the tub

during the wash and spin cycles.

OUTER TUB ASSEMBLY

The outer tub assembly is supported by two suspension

springs and stabilized by two air shock assemblies.

Cement counter weights are mounted to the outer tub

front (top & bottom), and the rear top. These counter

weights prevent excessive oscillation of the entire sus-

pended assembly during an unbalanced spin cycle.

INNER TUB ASSEMBLY

The inner tub is constructed of stainless steel. The

circumference of the tub is perforated to allow water to

flow through the tub as it revolves. A heavy steel shaft

is pressed into the tub support which is bolted to the tub.

The tub is supported by two ball bearings pressed into

the rear of the outer tub.

A large drive pulley is mounted to the free end of the

shaft that extends through the rear of the outer tub.

There are three plastic vanes mounted to the tub to aid

in the washing action during the wash cycle. The

rotation of the tub provides both the washing action

during the wash cycle, and water extraction during the

spin cycle.

Содержание WSXH208T




















































Результаты поиска

Содержание WSXH208T

Отзывы:

GE WSXH208T, Техническое обслуживание руководство, Страница: 17 / 51

Результаты поиска

Содержание WSXH208T

Отзывы: