manualshive.com logo in svg

GE Simon Security System, Руководство по установке

Поделиться
Скачать
GE Simon Security System Скачать руководство пользователя страница 18

Simon Security System

11

Interior sirens must always be wired with a resistor in the circuit. For circuit supervision 
which allows the panel to detect if the siren wire is cut (open), Option 53: Hardwire 
Siren Supervision must be turned on (see the “Programming” section).

LD105 Hardwire Interior Siren

Note  
Do not install the resistor at 
the panel terminals. This 
does not provide supervision 
of the wire.

Connect the LD105 Hardwire Interior Siren (13-374) to the panel using a 4.7k resistor 
(included with siren) as shown in Figure 4. The resistor must be connected across the 
siren wires as close to the siren as possible.

Note  
If you are installing only an 
interior siren and no exterior 
siren and Option 53 is on, 
you must connect a 4.7k 
resistor between the HWIN1 
and DCOUT terminals.

Figure 4. Hardwire Interior Siren with Supervision

Wiring Exterior Sirens

Panel terminal HWIN2 can be used for connecting exterior sirens and activates when 
intrusion and fire alarms occur.

Exterior sirens can be wired with or without a resistor in the circuit for supervision. For 
circuit supervision which allows the panel to detect if the siren wire is cut (open), 
Option 53: Hardwire Siren Supervision must be turned on (see the “Programming” sec-
tion).

Hardwire Exterior Siren with Supervision

Note  
Do not install the resistor at 
the panel terminals. This 
does not provide supervision 
of the wire.

Connect the Hardwire Exterior Siren (13-046) to the panel using a 4.7k resistor 
(included with siren) as shown in Figure 5. The resistor must be connected across the 
siren wires as close to the siren as possible.

Note  
If you are installing only an 
exterior siren and no interior 
siren and Option 53 is on, 
you must connect a 4.7k 
resistor between the HWIN2 
and DCOUT terminals.

Figure 5. Hardwire Exterior Siren with Supervision

H W I N 2

H W I N 1

D C O U T

A C

A C

Red

Black

4.7k Resistor
(located at siren)

H W I N 2

H W I N 1

D C O U T

A C

A C

4.7k Resistor

(located at siren)

Black

Red

Содержание Simon Security System





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды