GE Profile PSB42LGRBV Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 72

– 52 –

Service Diagnostics

Diagnostic Mode

1. To enter the diagnostic mode, the temperature

display must be lit up. If the temperature
display is not lit, press any pad on the overlay.

ICE DISPENSER

HOLD 3 SECS

LIGHT

QUICK ICE

CUBED

CRUSHED

WATER

DOOR ALARM

LOCK

RESET FILTER

HOLD FOR

3 SECS

TO ACTIVATE

COLDER

WARMER

DISPLAY

TEMP

COLDER

WARMER

0 º F IS RECOMMENDED

ADJUST TEMPERATURE

37 º F IS RECOMMENDED

REFRIGERATOR

FREEZER

2. Press

the

2

COLDER

and 2

WARMER

pads

simultaneously for three seconds. The

FREEZER

and

REFRIGERATOR

displays will change to

0 0

.

4.

Once the displays indicate a test mode, press
any pad on the temperature board overlay,
other than the

COLDER

or

WARMER

pads, to enter

that mode.

Note:

A test mode must be selected within 30

seconds of entering the diagnostic mode or it
will time out, normal refrigerator operation will
resume, and the displays will turn off. Once a test
mode is selected, the display will ﬂ ash to conﬁ rm
the mode selected.

5. At the end of a test session, to exit the

diagnostic mode, do one of the following:

• Enter

1

on the

FREEZER

display and

5

on

the

REFRIGERATOR

display. Press any pad

other than the

COLDER

or

WARMER

pads to

execute a system restart.

• Enter

1

on the

FREEZER

display and

6

on

the

REFRIGERATOR

display. Press any pad

other than the

COLDER

or

WARMER

pads to

exit the service diagnostic test mode.

•

Recycle power to the unit through the
main switch. As a cautionary measure,
the system will automatically time out of
the diagnostic mode after 15 minutes of
inactivity. In the diagnostics mode, the unit
can be tested under different conditions.

COLDER

WARMER

COLDER

WARMER

0 º F IS RECOMMENDED

ADJUST TEMPERATURE

37 º F IS RECOMMENDED

REFRIGERATOR

FREEZER

Press Simultaneously

3. To select a test mode:

a. Enter a numeric value (see

Test Mode

Char

t) on the

FREEZER

display using the

COLDER

or

WARMER

pad.

Note:

The

COLDER

pad decreases the numeric

value. The

WARMER

pad increases the numeric

value.

b. Enter a numeric value (see

Test Mode

Char

t) on the

REFRIGERATOR

display using

the

COLDER

or

WARMER

pad.

«
...
50
51
52
53
54
...
»

Содержание Profile PSB42LGRBV









































































Отзывы:

Нет отзывов

Похожие инструкции для Profile PSB42LGRBV

Бренд: Lec Страницы: 16

Бренд: iGenix Страницы: 16

FX Series FX2-4N1WS

Бренд: Randell Страницы: 2

Бренд: U-Line Страницы: 55

Бренд: BOMANN Страницы: 36

HSM25GFRESA and

Бренд: Hotpoint Страницы: 88

Бренд: inventum Страницы: 60

Бренд: inventum Страницы: 64

Бренд: Accucold Страницы: 14

Бренд: Engel Страницы: 1

Бренд: U-Line Страницы: 25

Бренд: Haier Страницы: 22

Бренд: Haier Страницы: 5

Бренд: Haier Страницы: 28

Бренд: Haier Страницы: 32

Бренд: Haier Страницы: 48

Бренд: Haier Страницы: 18

Бренд: Haier Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды