GE Profile PSB42LGRBV Скачать руководство пользователя страница 42

Страница: 42 / 72

– 42 –

To remove the condenser fan assembly:

1. Remove the water ﬁ lter cartridge.

2. Remove the 2 Phillips-head screws from the

water ﬁ lter receptacle.

3. Remove the 2 Phillips-head screws from the

front of the shroud assembly and disconnect
the fan wiring.

4. Bend the 2 wire retention tabs back to release

the wire harness.

5. Pull the fan forward and tilt it to the left to

release the 2 water ﬁ lter tubes from the
channel at the top of the condenser fan motor
shroud.

The 3-bladed fan can be removed without
removing the complete fan assembly.

The fan rotates counterclockwise as viewed from
the motor shaft end. It is held in place by a spring
retention clip.

Top View

Installing the condenser fan assembly:

1. Secure the wires to the condenser fan shroud

to prevent interference with the fan blade
rotation.

2. Ensure the rubber tab covers are in place

when reinstalling the condenser fan assembly.

Cabinet Wiring

Fan Assembly

Tab

3. Ensure water ﬁ lter lines are fully seated into

the top channel of the water ﬁ lter housing
bracket.

Voltage Checks

When the power control board (PCB) is
energizing the fan, check for approximately 9
to10 VDC between pin #2 and pin #3 at CN02
on the terminal block. Check for approximately
2 VDC between pin #1 and pin #3 at CN02.

6. Pull the cabinet wiring down as shown in the

photo below. Carefully pull the condenser fan
assembly out of the machine compartment.

CN02

RED

LIGHT BLUE

GRAY

BROWN

PURPLE

GRAY

1
2
3

BLDC C-FAN

Tab

Содержание Profile PSB42LGRBV









































































Результаты поиска

Содержание Profile PSB42LGRBV

Отзывы:

Похожие инструкции для Profile PSB42LGRBV

Бренды по названию

Популярные бренды

GE Profile PSB42LGRBV, Техническое обслуживание руководство

Результаты поиска

Содержание Profile PSB42LGRBV

Отзывы:

Похожие инструкции для Profile PSB42LGRBV

Бренды по названию

Популярные бренды