GE Profile PSB42LGRBV Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 72

– 33 –

3. Slide motor assembly to the left to clear the

rear mounting tabs.

4. Pull the motor forward while rotating it

clockwise.

5. Disconnect the motor wire connector.

Caution:

When assembling, ensure the duct

door post is in the outer channel of the cam, to
avoid damage to the duct door and/or cam.

Cam

Duct Door Post

Dispenser Switch

The dispenser switch pad must be removed to
access the dispenser switch. Insert a ﬂ at-blade
screwdriver into the bottom slot of the dispenser
switch pad and lift up.

To remove the switch, lift it up at the bottom (see
photo) with a screwdriver. Release the switch
from the tabs at the top.

Switch

Dispenser Switch Pad

Caution:

When installing the motor, ensure the

motor mount is behind the side and bottom tabs,
or damage to the cam will occur.

Tab

Tab

Note:

Before reapplying power, remove the

switch housing and rotate the motor cam
clockwise by hand to ensure proper door/cam
operation. To avoid motor gear damage, DO NOT
rotate the motor cam counterclockwise.

The duct door motor operates at 120 VAC when
energized by the power control board (PCB).
The motor has resistance of approximately 2K

Ω

.

Check at CN08 on the terminal board, between
pin # 4 (neutral) and pin # 6.

GEARED MOTOR-DISP

DISPENSER HEATER

4

3

2

RED

BROWN

WHITE

4
5
6

CN08

The switch is a normally open switch. Check for
5 VDC at CN03 on the terminal board, between
pin #3 and pin #4, when the dispenser switch is
open.

«
...
31
32
33
34
35
...
»

Содержание Profile PSB42LGRBV









































































Отзывы:

Нет отзывов

Похожие инструкции для Profile PSB42LGRBV

Бренд: Daikin Страницы: 72

Бренд: Accucold Страницы: 12

Бренд: Gaggenau Страницы: 30

Бренд: Kelvinator Страницы: 16

Бренд: iGenix Страницы: 12

Бренд: Engel Страницы: 20

Бренд: Landmark Страницы: 32

Party Cooler none

Бренд: Equator Страницы: 4

Бренд: Oceanic Страницы: 74

Бренд: Salora Страницы: 35

Бренд: NEFF Страницы: 95

S HOME SC-430AU8TMW

Бренд: Seiki Страницы: 20

Бренд: Jenn-Air Страницы: 6

GTS18DBPFLCC and

Бренд: GE Страницы: 96

GTH21SBXASS and

Бренд: GE Страницы: 108

GTS18ABSALWW and

Бренд: GE Страницы: 88

Бренд: Haier Страницы: 32

Бренд: Haier Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды