GE Profile PSB42LGRBV Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 72

– 44 –

Freezer Evaporator Assembly

The freezer evaporator assembly consists of an
evaporator, defrost and drain heaters, defrost
safety thermostat, thermistor, and fan assembly.
All the parts are available as a complete
replacement assembly, or the components are
available individually.

All components are housed together and installed
in a recessed compartment in the freezer ceiling.

To access the freezer evaporator assembly:

1. Remove the ice container shelf, then remove

the icemaker.

2. Remove 4 Phillips-head screws that hold the

top air duct cover in place.

3. Remove auger motor and cube motor

connectors from the freezer evaporator cover.

4. Remove the 2 Phillips-head screws that hold

the rear air duct cover in place, then pull it
down.

5. Disconnect all the electrical connectors from

the ceiling.

6. Remove the rear air duct cover.

7. Remove the 2 Phillips-head screws from the

suction line drain pan and heater assembly.
Disconnect the associated wiring.

Note:

The suction line drain pan heater has a

resistance value of 1.3K

Ω

.

Rear Air Duct Cover

Air Duct Cover

Connectors

Styrofoam Air Duct

8. Carefully remove the styrofoam air duct.

Note:

The styrofoam air duct is held in place by

adhesive.

Drain Pan

«
...
42
43
44
45
46
...
»

Содержание Profile PSB42LGRBV









































































Отзывы:

Нет отзывов

Похожие инструкции для Profile PSB42LGRBV

Бренд: Accucold Страницы: 12

Бренд: ChiQ Страницы: 9

Бренд: VWR Страницы: 26

Бренд: Marvel Страницы: 1

Бренд: Galaxy Страницы: 64

Бренд: U-Line Страницы: 50

Бренд: Jenn-Air Страницы: 44

FRN-U20DA Series

Бренд: Daewoo Страницы: 56

Бренд: Avanti Страницы: 16

Бренд: Hotpoint Страницы: 16

Diplomat DAR0488BL

Бренд: Danby Страницы: 13

Бренд: Hisense Страницы: 65

Бренд: GE Страницы: 2

Бренд: ZANKER Страницы: 32

Бренд: Hotpoint Страницы: 2

Refrigerated Champagne Cellar 3SWCCE

Бренд: Marvel Страницы: 10

Бренд: Yeticool Страницы: 7

Бренд: Indesit Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды