GE Profile PSB42LGRBV Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 72

– 48 –

Fresh Food Evaporator Assembly

The fresh food evaporator assembly consists
of an evaporator, defrost and drain heaters,
bimetal defrost safety thermostat, thermistor, and
evaporator fan assembly.

All components are housed together and
installed in the refrigerator interior in a recessed
compartmet in the refrigerator ceiling. This
compartment extends vertically into the machine
compartment.

To access the fresh food evaporator
assembly:

1. Remove the fresh food grille cover by

inserting a ﬂ at-blade screwdriver into the slot
(see photo) and lifting up.

2. Remove 4 Phillips-head screws from the

fresh food air duct cover. Pull the front of the
cover down.

3. Disconnect the thermistor and lighting

connector. Remove the fresh food air duct
cover.

Air Duct Cover

Lighting Connector

Thermistor Connector

4. Remove the 4 Phillips-head screws that hold

the refrigerator suction line drain assembly in
place. Remove the assembly.

5. Remove the 2 Phillips-head screws that hold

the fresh food upper duct cover assembly in
place. Remove the upper duct cover.

6. Disconnect the remaining electrical

connectors.

7. Remove 2 Phillips-head screws from the fresh

food evaporator housing.

«
...
46
47
48
49
50
...
»

Содержание Profile PSB42LGRBV









































































Отзывы:

Нет отзывов

Похожие инструкции для Profile PSB42LGRBV

Бренд: Haier Страницы: 23

Бренд: Haier Страницы: 88

Бренд: Haier Страницы: 7

Бренд: Saivod Страницы: 26

Бренд: FAVORIT Страницы: 76

Бренд: Kirsch Страницы: 84

Бренд: Zanussi Electrolux Страницы: 16

Бренд: Norcold Страницы: 26

Бренд: Adler Europe Страницы: 72

Бренд: Samsung Страницы: 38

Бренд: Samsung Страницы: 38

Бренд: Samsung Страницы: 38

Бренд: Samsung Страницы: 42

Бренд: Samsung Страницы: 8

Бренд: GE Страницы: 5

GFSF6KEXBBB and

Бренд: GE Страницы: 108

Бренд: GE Страницы: 42

GFSF6KEXABB and

Бренд: GE Страницы: 112

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды