GE Profile PSB42LGRBV Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 72

– 51 –

Replacing the Freezer or Fresh Food
Evaporator

The freezer evaporator can be replaced as a
complete unit, including the defrost components
and fan assembly, or it can be replaced as an
individual component.

The fresh food evaporator can be replaced as
a complete unit or as an assembly consisting of
the evaporator and defrost heater (the fresh food
defrost heater is not available separately).

To replace the freezer or fresh food
evaporator:

1. Access the speciﬁ c evaporator as described

in

Fresh Food Evaporator Assembly

or

Freezer

Evaporator Assembly

.

2. In the machine compartment, remove the

screws that hold the main switch in place.
Move the main switch out of the way to
provide better access to the evaporator
tubing.

Note:

Save the insulation to rewrap the

refrigerant tubing after brazing.

7. Recover the refrigerant. (See

Evacuation and

Charging Procedures

).

8. Disconnect the suction line and capillary of

the speciﬁ c evaporator to be replaced. Note
the position of the tubing within the machine
compartment. Pull the evaporator tubing down
from the cabinet and remove the evaporator.

9. Install the new evaporator and carefully bend

the tubing to the correct position. Braze the
suction line and capillary tubing.

10. Replace the drier (part # WR86X93) and

install a process valve (part # WJ56X61) at
the compressor.

11. Reinstall the remaining components within

the cabinet section while the braze joints are
cooling.

12. Charge the system with the exact amount of

refrigerant (8.11 oz.) speciﬁ ed on the rating
plate

13. Check for refrigerant leaks at all joints.

14. Reinstall insulation around the tubing. Wrap

with tape to provide a good airtight seal.

15. Reinstall Styrofoam block and metal cover.

16. Check refrigerator for proper operation.

Note:

Adhesive may be holding the Styrofoam

block in place after the metal cover is removed.

Capillary Tubing

Suction Line

6. Carefully cut and remove the insulation on the

suction line and capillary tubing to expose the
solder joints.

3. Remove the condenser fan assembly from the

compartment. (See

Fans

.)

4. Remove the 5 Phillips-head screws holding

the metal cover over the Styrofoam block (see
photo below). Remove the metal cover.

5. Remove the Styrofoam block from the base of

the evaporator tubing.

Evaporator Tubing

Main Switch

Styrofoam Block

Metal Cover

«
...
49
50
51
52
53
...
»

Содержание Profile PSB42LGRBV









































































Отзывы:

Нет отзывов

Похожие инструкции для Profile PSB42LGRBV

Бренд: KBS Страницы: 96

Бренд: JUNO Страницы: 32

Бренд: McCall Страницы: 2

Бренд: Waeco Страницы: 112

Бренд: Zanussi Electrolux Страницы: 20

Бренд: U-Line Страницы: 50

Бренд: Dacor Страницы: 48

Monogram ZFSB23DRSS

Бренд: Monogram Страницы: 2

Бренд: Saba Страницы: 30

Бренд: Danby Страницы: 16

Бренд: ZANKER Страницы: 36

Бренд: Jenn-Air Страницы: 64

Бренд: baridi Страницы: 4

Бренд: Gram Страницы: 132

Profile PFSS5PJYSS

Бренд: GE Страницы: 2

PFSS6SKXSS - Profile 25.8 cu. Ft....

Бренд: GE Страницы: 2

Profile PSW26PSWSS

Бренд: GE Страницы: 3

PSHS6YGXSS - Profile 26' Dispenser...

Бренд: GE Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды