GE GeoSpring GEH50DEED Скачать руководство пользователя

Страница: 61 / 78

– 61 –

To replace the electronic expansion valve (EEV):

1. Turn power off.

2. Remove the rear shroud cover and the

rear shroud as 1 assembly. (See

Machine

Compartment Covers

3. Remove the evaporator inlet sensor from

the evaporator inlet tubing. (See

Temperature

Sensors

6. If you are using a torch to replace the EEV

valve, unsolder the EEV from the drier inlet tube

and the evaporator inlet tube using currently

accepted procedures.

7. Apply a liberal amount of heat-absorbing

thermal paste, such as Part #WX5X8927, to the

replacement EEV.

9. Install the evaporator inlet sensor to the

evaporator inlet tube, then insulate the sensor

location with new mastic (Part #WS03X10075).

Coil

Detent

Indent

Clip

Detent

EEV

4. Rotate the coil until the indent on the coil clip is

between detents on the valve body.

5. Lift the coil from the valve body.

Evaporator Inlet Sensor

Thermal Paste

8. Braze the dryer inlet tube and the evaporator

inlet tube using silfos.

Содержание GeoSpring GEH50DEED















































































Результаты поиска

Содержание GeoSpring GEH50DEED

Отзывы:

Похожие инструкции для GeoSpring GEH50DEED

Бренды по названию

Популярные бренды

GE GeoSpring GEH50DEED, Техническое обслуживание руководство

Результаты поиска

Содержание GeoSpring GEH50DEED

Отзывы:

Похожие инструкции для GeoSpring GEH50DEED

Бренды по названию

Популярные бренды