manualshive.com logo in svg

GE GeoSpring GEH50DEED, Техническое обслуживание руководство

Поделиться
Скачать
GE GeoSpring GEH50DEED Скачать руководство пользователя страница 12

– 12 –

Dry Tank Test

Upon initial installation, or anytime the power is off and power is then connected, the water heater will run a 

dry tank test before starting the selected heating mode.

After approximately 2 minutes, the control will turn on the compressor and fan motor. The control will run 

the sealed system for 5 minutes and monitor the tank temperature from the T2 sensor. if the control sees 

a temperature rise of more than 3.5 degrees within the 5 minutes, it assumes the tank is empty, shuts off 

heat, and displays an F11 fault code warning to fill the tank (a full tank would absorb the heat, and the 

temperature increase would take longer). 

Note:

 in the event of a power loss, when power is restored, the control will resume whatever heating mode 

had been operating prior to power loss. 

Sealed System Startup

Ambient

temperature OK?

45F< T5 >120F

Switch to electric

No

Is evaporator

free of frost?

T3a >32F

No

Yes

Start Sealed System

Yes

Ensure compressor

has been off for at

least 2 minutes

element

Switch to electric

element

The upper limit avoids a 

compressor overheat, the lower 

limit prevents liquid refrigerant 

from entering the compressor  

as well as inefficiency due to the 

lack of heat in the air.

room temperature between 

45°F and 120°F and 

evaporator above 32°F?

Start sealed system.

(Continued Next page)

Содержание GeoSpring GEH50DEED















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды