GE GeoSpring GEH50DEED Скачать руководство пользователя

Страница: 46 / 78

– 46 –

Note:

When installing the evaporator inlet sensor, be

sure to insulate the sensor location with new mastic

(part #WS03X10075).

(Continued Next page)

The sensor is inserted into a clip that is attached

to the evaporator inlet tube. The sensor location

is insulated with mastic. (See

Component Locator

Views

The rear shroud cover and rear shroud must be

removed to access the evaporator inlet sensor. (See

Machine Compartment Covers

Mastic

Evaporator Outlet Sensor

The evaporator outlet sensor (T3b) provides the

control with evaporator outlet temperature during

sealed system operation.

The control checks the sensor to confirm:

1. Temperature difference between T3a and T3b is

greater than 5°F after 30 minutes compressor

run time.

2. The T3a, T3b, and T5 sensors are all within 15°F

of each other before the compressor starts.

3. The electronic expansion valve (EEV) is operating

properly and valve rotation is within range.

4. The condition of the sensor is either open or

shorted. The sensor is considered open if the

voltage at control board location T3b is greater

than 4.88 VDC, and shorted if less than 0.098

VDC.

if any of the above tests fail, the control will stop

the sealed system and operate the water heater in

electric mode.

Specific failures associated with the evaporator

outlet sensor can initiate fault codes Fd, FF, and F6.

(See

Service Mode.)

The sensor is inserted into a clip that is attached

to the evaporator outlet tube. The sensor location

is insulated with mastic. (See

Component Locator

Views

The rear shroud must be removed to access the

evaporator outlet sensor. (See

Machine Compartment

Covers

Evaporator Inlet Tube

Evaporator Inlet Sensor

Clip

Evaporator Outlet Sensor

Evaporator Outlet Tube

Clip

Note:

Sensors T3A, T3b, and T4 are supplied as an

assembly (part #WS17X10014).

Содержание GeoSpring GEH50DEED















































































Результаты поиска

Содержание GeoSpring GEH50DEED

Отзывы:

Похожие инструкции для GeoSpring GEH50DEED

Бренды по названию

Популярные бренды

GE GeoSpring GEH50DEED, Техническое обслуживание руководство

Результаты поиска

Содержание GeoSpring GEH50DEED

Отзывы:

Похожие инструкции для GeoSpring GEH50DEED

Бренды по названию

Популярные бренды