GE GeoSpring GEH50DEED Скачать руководство пользователя

Страница: 39 / 78

– 39 –

Water Heater Components

NOTICE:

removal and/or replacement of the

following components of the water heater requires a

certified plumber:
•

Anode rod

•

Dip Tube

•

Drain Valve

•

Elements

•

Temperature and pressure Valve

Machine Compartment Covers

There are 4 covers that enclose the machine

compartment. The front shroud cover is vented to

allow air intake to the evaporator and provides slots

to attach the air filter. The control panel is attached

to the front shroud. The rear shroud is vented to

allow air to exhaust from the evaporator. The rear

shroud cover contains the electrical junction box

and covers the top of the fan shroud.

To remove the front shroud cover:

Remove the air filter. (See

Control Features

Cleaning the Filter

2. remove the two T-20 Torx screws from the top

of the trim ring.

3. Lift the front of the trim ring, push it back, then

suspend it from the water heater.

4. remove the nine T-20 Torx screws from the front

shroud cover.

5. Lift the front shroud cover and remove it from

the water heater.

Trim Ring

Front Shroud Cover

(Continued Next page)

Содержание GeoSpring GEH50DEED















































































Результаты поиска

Содержание GeoSpring GEH50DEED

Отзывы:

Похожие инструкции для GeoSpring GEH50DEED

Бренды по названию

Популярные бренды

GE GeoSpring GEH50DEED, Техническое обслуживание руководство

Результаты поиска

Содержание GeoSpring GEH50DEED

Отзывы:

Похожие инструкции для GeoSpring GEH50DEED

Бренды по названию

Популярные бренды