manualshive.com logo in svg

GE GeoSpring GEH50DEED, Техническое обслуживание руководство

Поделиться
Скачать
GE GeoSpring GEH50DEED Скачать руководство пользователя страница 58

– 58 –

To verify that the compressor is running:

WARNING

: During normal operation, the  

temperature of the single-speed compressor may 

be hot. Use caution to avoid injury and wear Kevlar

®

 

gloves or equivalent protection. 

Disconnect power from the unit. Wait 2 minutes for 

pressure to equalize.

 

place a hand on the chassis, 

near the compressor. reconnect power and feel for 

a vibration when the compressor tries to start. 

Note:

 The compressor will not start right away. The 

control will wait 2 minutes, then the single-speed 

compressor will start.

The control will record a compressor fault if the 

current is less than 1.5 amps when the compressor 

relay on the board is energized.

refer to the compressor replacement instructions 

included with the replacement compressor. 

Evacuate and recharge the system using currently 

accepted procedures. (See 

Evacuation and Charging 

Procedure

.)

Bracket

Single-Speed Compressor

The compressor is a reciprocating type. refer to 

the mini-manual for the BTU/hour rating and the 

compressor capacity test specification. 

The compressor utilizes a start capacitor rated 

at 145 to 177 ufd. The capacitor is installed in a 

bracket that is attached to the top of the relay cover.

 

Start Capacitor

it is necessary to remove the control panel to access 

the compressor external overload. (See 

Control 

Panel

.)

External 

Overload

(Continued Next page)

in the event the compressor is shorted to ground, 

the compressor utilizes an external overload 

that removes L1 voltage from the compressor,  

providing additional protection. The overload opens 

at 14 amps within 6.5 to 16 seconds and opens  

when temperature exceeds 158°F. it will reset 

automatically. 

it is attached to the inside of the control panel rear 

cover with a 1/4-in. hex-head screw. 

Содержание GeoSpring GEH50DEED















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды