background image

Druck ADTS 405 Service Manual

K171 Issue No. 1

Page 1-1

Chapter 1

Description

CONTENTS

Para.

Introduction.........................................................................................1
SPECIFICATION
DESCRIPTION
ADTS 405 and Electronics Rack (ADTS 405F) .......................5
Pitot and Static Controllers ..........................................................11

Operation ................................................................................14
Pressure output ....................................................................19
Soft start ..................................................................................21

Control computer and communications ...............................22
ARINC 429 Interface (special order) .........................................23
Altimeter Encoder Interface (special order)..........................24
IEEE 488 Interface (option E) .... 25
Pump Rack...........................................................................................26
Hand terminal ....................................................................................31

Illustrations

fig.

ADTS 405 General view .................................................................1-1
ADTS 405F General view ...............................................................1-2
ADTS 405 ..............................................................................................1-3
ADTS 405F Racks ..............................................................................1-4
ADTS 405 and Electronics Rack Internal view.....................1-5
Controller PCB Schematic.............................................................1-6
Ps Manifold Schematic...................................................................1-7
Pt Manifold Schematic ...................................................................1-8
Supervisor Computer and Communications .......................1-9
Pump Rack...........................................................................................1-10
Hand terminal ....................................................................................1-11

Содержание Druck ADTS 405

































































Отзывы: