GE Druck ADTS 405 Скачать руководство пользователя | Manualshive

Страница: 33 / 64

background image

Druck ADTS 405 Service Manual

K0171 Issue No. 1

Page 2-9

Fan

56.

Pull back the outer sleeving as necessary to gain access to the cables. Cut and remove any

tyraps securing the cable loom. Disconnect the red and black cables at the terminal block under the
front panel.

57.

From the top of the pump front panel, unscrew and remove the four screws, stiff nuts and plain

washers securing fan cover to fan.

58.

Unscrew and remove the four hexagonal socket cap-screws securing the fan to the front panel

(this breaks the water seal). Remove the fan.

PSU Motor Controller Assembly

59.

Cut and remove any tyraps securing the cable looms attached to the PSU.

60.

Disconnect the electrical connectors from the PSU and motor controller.

61.

Unscrew and remove the two screws and plain washers securing the motor controller PCB.

62.

Unscrew and remove the four screws and shakeproof washers securing PSU.

63.

Remove the motor controller and PSU.

«
...
31
32
33
34
35
...
»

Содержание Druck ADTS 405

































































Отзывы:

Нет отзывов

Похожие инструкции для Druck ADTS 405

Бренд: Lambrecht Страницы: 5

Бренд: Keithley Страницы: 25

Бренд: WAGER Страницы: 36

Бренд: Oceanic Страницы: 152

Бренд: Kaiterra Страницы: 8

Бренд: Kaiterra Страницы: 12

Бренд: velocomp Страницы: 4

Бренд: Det-Tronics Страницы: 18

Бренд: Kane Страницы: 35

Бренд: Veris Страницы: 3

Бренд: Hanna Instruments Страницы: 2

TEMS AUTOMATIC - 2

Бренд: ASCOM Страницы: 12

Бренд: Parker Страницы: 16

Бренд: Waterproof Страницы: 51

Бренд: SellEton Scales Страницы: 30

Бренд: Kawai Страницы: 2

Бренд: Omega Страницы: 59

Бренд: Veeder-Root Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды