GE Druck ADTS 405 Скачать руководство пользователя страница 38

Страница: 38 / 64

Druck ADTS 405 Service Manual

K0171 Issue No. 1

Page 3-4

15.

Locate a new bonded seal to the right-angle fitting and connect the vacuum pipe to the pump

unit.

16.

Connect the pressure pipe to the bowl filter.

Pump Front Panel

17.

Carefully align the front panel over the partially assembled pump unit and secure with the four

countersunk screws.

18.

Refer to final assembly para. 51.

ADTS 405 and Electronics Rack (ADTS 405F)

Power Supply Unit

19.

Fit the PSU board to the motherboard. Locate the cover over the PSU board.

20.

Route the earth bonding wire through the p-clips. Connect the earth bonding wire to the stud on

the front panel.

21.

Secure the PSU cover to the side panel of the rack with the eight screws and shakeproof

washers.

22.

Carefully locate the Pt controller PCB on the studs of the side panel. Secure the Pt controller PCB

with the four spacers and nuts.

23.

Secure the PSU cover to the rear panel of the rack with the four screws and shakeproof washers.

24.

Connect the nine-pin connector to the PSU cover.

Manifold Assembly (Figure 3-1)

25.

Locate the manifold on the front panel and secure with the two screws.

26.

Position the connectors through the slots in the side panels.

27.

Carefully insert the output fittings through the front panel into the manifold, rotating slightly to

ease fitment. Secure each fitting with two screws. Refit the p-clips securing the cable looms to the
manifold assembly.

28.

Connect the two input pipes, one to the front panel Ps connector and the other to the pressure

regulator. Connect the cables to the solenoid valves, refer to table 3-1.

Note:

For solenoids with a moulded connection refit the solenoid over the valve and
screw on the washer and knurled securing nut.

Mimic panel

29.

Locate the mimic panel on the front panel and secure with the seven nyloc nuts and plain

washers.

30.

Connect the ribbon cable to the mimic panel.

Содержание Druck ADTS 405
































































Результаты поиска

Содержание Druck ADTS 405

Отзывы:

Бренды по названию

Популярные бренды

GE Druck ADTS 405, Руководство по обслуживанию

Результаты поиска

Содержание Druck ADTS 405

Отзывы:

Бренды по названию

Популярные бренды