GE Druck ADTS 405 Скачать руководство пользователя

Страница: 52 / 64

Druck ADTS 405 Service Manual

K171 Issue No. 1

Page 5-4

Procedure

17.

The calibration check should be carried out with the ADTS 405 in the normal operating mode.

The following equipment is required:

Note:

Equivalent substitutes can be used.

•

Pressure standard

accuracy ±0.01%FS

absolute and gauge

•

IBM PC

with IEEE 488 interface

(1)

Connect the pressure standard.

(2)

Switch on the ADTS 405 and wait for the start-up sequence to take place.

(3)

After a successful start-up sequence, enter the calibration mode by simultaneously

pressing keys F1 and F4.

The display shows:

(CALIBRATION)

F1 MAIN CALIBRATION
F2 CALIBRATION CHECK
F3 RATE CALIBRATION

Note: The main calibration facility is used at depot level by qualified personnel.

(4)

Press F 2 - Calibration check.

(5)

Switch on the pump unit.

(6)

Select the pressure source - internal.

(7)

Set the channel to be checked:

Ps
Pt
Ps and Pt

(8)

Select the combined channel check - Ps and Pt.

Note: For only checking the Ps channel, use the values in table 5-2.

(9)

Enter the first aim value in table 5-1 and record the value on the pressure standard.

(10) Repeat this for further values in table 5-1 until after point 8 press [Ps END].

CAUTION: THE Ps SENSOR WILL BE OVER-PRESSURED AND DAMAGED UNLESS [PsEND] IS
SELECTED.

(11) Enter the remaining values in table 5-1 for the Pt channel and then press [Pt END].

(12) Compare the recorded values and with the applied values, the difference must not be greater
than ±0.012% Ps and ±0.015% Pt of the applied values.

(13) If the difference exceeds these values, repeat the procedure. If the differences still exceed these
values, return the unit to depot.

Содержание Druck ADTS 405
































































Результаты поиска

Содержание Druck ADTS 405

Отзывы:

Похожие инструкции для Druck ADTS 405

Бренды по названию

Популярные бренды

GE Druck ADTS 405, Руководство по обслуживанию

Результаты поиска

Содержание Druck ADTS 405

Отзывы:

Похожие инструкции для Druck ADTS 405

Бренды по названию

Популярные бренды