Gasmet DX4040 Скачать руководство пользователя страница 69

Страница: 69 / 75

DX4040 INSTRUCTION AND OPERATING MANUAL (E2.04)

APPENDIX B: INSTALL/UNINSTALL CALCMET LITE

The following procedure explains how to install or upgrade Calcmet Lite:

Backup the following files installed on

the PDA (under: My Device\Program

Files\CalcmetLite\) on your computer

via USB connection:

CALCMETLITE.INI,

HardwareLimits.txt and

CALCMET.BKG.

Go then to: Start → Settings →

System → Remove Programs.

Click onto “Gasmet Technologies Oy

CalcmetLite” and click “Remove”.
“Remove Program”: Yes

Restart the PDA if requested.

Calcmet Lite Setup package is

a “*.cab” file. This file is used

to install Calcmet Lite onto the

PDA memory. Transfer the

setup file on the “My

Documents” directory of the

PDA.

Click onto the

“CalcmetLite____.cab” file in

order to start the installation.

During installation and if you

have on your PDA an external

Storage Card, the installation

routine can prompt the location

of the installation. Choose to

install Calcmet Lite on the

“Device”.

After installation, go to: Start →

Settings → Today → Items

(tab) and just click “ok” in the

top right end corner. This will

enable Calcmet Lite shortcut in

the “Today” window.

Transfer back (copy) the

following files onto the PDA (My Device\Program Files\CalcmetLite\): CALCMETLITE.INI,

HardwareLimits.txt and CALCMET.BKG

Calcmet Lite installation/upgrade is over.

Содержание DX4040












































































Результаты поиска

Содержание DX4040

Отзывы:

Похожие инструкции для DX4040

Бренды по названию

Популярные бренды

Gasmet DX4040, Инструкция по эксплуатации и руководство пользователя

Результаты поиска

Содержание DX4040

Отзывы:

Похожие инструкции для DX4040

Бренды по названию

Популярные бренды