13–8–612 Page 36
SYMPTOM
POSSIBLE CAUSE
REMEDY
“MOTOR OVERLOAD” (Continued)
4.
Imbalanced amps.
4.
Rotate 3 phase power leads.
If the high reading stays on
the same leg, the problem is
with the motor.
If the high reading moves
with the lead, the problem
is with the incoming power.
5.
Incorrect motor overload
5.
Set overload to motor name–
setting.
plate amps.
“CHANGE AIR FILTER” light on.
1.
Dirty air filter.
1.
Clean or replace.
“CHANGE AIR FILTER” light on,
1.
Loose connections.
1.
Clean and tighten
and WILL NOT RESET.
connections.
2.
Faulty vacuum switch.
2.
Measure the AC voltage
between wire number 7 and
wire number #6 at board.
If the reading is zero,
replace the vacuum switch.
2.
Control board fault.
2.
Measure the AC voltage
between wire number 7 and
wire number #6 at board.
If the reading is 24 volts,
replace the control board.
“MOTOR OVERLOAD”
1.
Loose connections.
1.
Measure the AC voltage
shutdown.
between wire number 5 and
(RELAY NOT TRIPPED)
wire number #6 at board.
If the reading is zero,
tighten the connections.
2.
Control board fault.
2.
Measure the AC voltage
between wire number 5 and
wire number #6 at board.
If the reading is 24 volts,
replace the control board.
“EO4”, Emergency Stop
1.
Loose connections or
1.
Tighten connection or
will not clear.
faulty switch.
repair or replace switch.
2.
Contact block not
2.
Ensure contact block is fully
properly installed.
snapped into left or right (not
center) slot of switch operator.
3.
Control board fault.
3.
Measure the AC voltage
between wire number 3 and
wire number #6 at board.
If the reading is 24 volts,
replace the control board.
Содержание EBB BB-7.5 HP
