background image

GAT NET.Lock 7000 System

 

Mounting 

 

16

 

HB_GAT-NETLOCK7000--EN_30

 

www.gantner.com

 

3.5  Mounting in Lockers with Non-Metallic Doors 

 
In lockers with non-metallic doors the GAT NET.Lock 7000 is mounted on the left or right inner locker wall (depending 
if it is a right or left locker) and the GAT NET.Lock Bolt Set 71x0 is mounted on the inside of the locker door.  Also a 
drilling in the locker door is required for the LED status display. See the following figure and the steps afterwards for 
the mounting instructions. 
 

 

 

1.  GAT NET.Lock 7000 

2.  GAT NET.Lock Bolt Set 7100 

3.  Mounting screws for the GAT NET.Lock 7000 (3x), type depending on the locker material 

4.  Door shackle 

5.  Door contact 

6.  Mounting screws for bolt set 

7.  LED (hole in the locker door) 

 

Figure 3.5

 - Mounting of the GAT NET.Lock 7000 in a locker with non-metallic door (right door) 

 
 
 
 

3.5.1  Important Measures when Mounting the GAT NET.Lock 7000 and Bolt Set (Non-Metal Doors) 

 
During the mounting, please pay particular attention to the following points: 
 
-  When the door is pressed shut, the gap between the bolt set and the front of the GAT NET.Lock 7000 must not 

exceed 0.5 mm. Ideally the bolt set should touch the front of the lock (see measure in Figure 3.5). 

 
-  The middle of the door shackle (4) must be 1 mm higher than the middle of the door shackle opening in the GAT 

NET.Lock  7000  (see measure  in  Figure 3.5)

. This ensures the door’s ability to close even if the door position is 

modified 3 mm downwards or 1 mm upwards (tolerance ±2 mm). 

 

Содержание GAT NET.Lock 7000









































Отзывы: