gamma scientific SpectralLED RS-7 Скачать руководство пользователя страница 81

Страница: 81 / 81

SpectralLED® RS-7 USER MANUAL

Page 80

API REVISIONS

Changes for X2:

Add GRP (Channel Grouping Disable/Enable) command

Add CGL (Channel Group List) command

Add PRE N (Preset Next) command

Add OCL (Offending Channels List) command

Add HLP & HELP command

Changes for X6:

Add CTY (Calibration Type) command

Add CAL (Calibration Information) command

Add ATF (Accessory Transfer Function) command

Add RST (Restart) command

Add OXYZ (Output Tristimulus) command

Add TXYZ (Target spectrum Tristimulus) command

Add CCT (Correlated Color Temperature) command

Add OUTC (Change Integrated Output Power with Constant Chromaticity) command

Add CCSx,y (Color-Correct Output Spectrum to explicit CIE 1931 x,y) command

Remove ADP (Allowable Drive Percentage) command

Remove SCC (Set Channel Current) command

Changes for X7:

Add PUL (Pulse) command

Add ICK (Integrity Check) command

Add RST (Restart) command

Add OPD (Output Port Differential) command

Add MON (Monitor System Query) command

Add PTY (Peak Type) command

Add BAT V (Basic Assurance Test – Verbose) command

Add SCANR (Scan Next Repeatedly) command

Add SCAD (Scan Demo) command

Add SDC (Spectral Calibration Data CRC32) command

Add IRI (Iris) command

Add POT (Power-On Time) command

Add ASA (Asynchronous Alarms) command

Add SDC (Spectral Data CRC32) command

Add IRI (Iris) command

Changes for X8:

Add IRR (Irradiance mode) command

Add CFC (Clear Fault Condition) command

Содержание SpectralLED RS-7


















































































Результаты поиска

Содержание SpectralLED RS-7

Отзывы:

gamma scientific SpectralLED RS-7, Руководство пользователя, Страница: 81 / 81

Результаты поиска

Содержание SpectralLED RS-7

Отзывы: