gamma scientific SpectralLED RS-7 Скачать руководство пользователя страница 23

Страница: 23 / 81

SpectralLED® RS-7 USER MANUAL

Page 22

Disconnect From COM Port:

Click to release the COM port, in order to allow another program to access it.

SpectralLED Assistant will re-connect to the RS-7 automatically whenever you perform any operation that

requires SpectralLED Assistant to communicate with the unit.

2b.

Tristimulus is 2

Standard Observer

Tristimulus is 10

Standard Observer

Selects the tristimulus color-matching functions to be either the CIE 1931 2° Standard Observer, or the CIE 1964

10° Standard Observer.

(ASCII Command API reference:

SOB

Section 4.5.5)

2c.

SI Photometric Units (lm/m², cd/m²)

US Photometric Units (fc, fL)

Selects between SI photometric units of

lm/m² (illuminance units of lumens per square meter, also known as

lux

)

cd/m² (luminance units of candela per square meter, also known as

nits

)

and US photometric units of

footcandles (illuminance units)

footLamberts (luminance units)

2d.

Peak Type

The wavelength of each of the RS-7’s channels, as seen for example when one hovers the mouse pointer over

one of the Individual Channel Power Level controls (

), or as generated by the Export Channel List function (see

Section 3.4), can be calculated in one of three ways:

Centroid

, which is the amplitude-weighted average of all wavelengths of the spectrum.

Peak

, which represents the peak (where 1

derivative = 0) of the parabola defined by the highest-amplitude

spectral data point and its two immediate neighbors:

Содержание SpectralLED RS-7


















































































Результаты поиска

Содержание SpectralLED RS-7

Отзывы:

gamma scientific SpectralLED RS-7, Руководство пользователя, Страница: 23 / 81

Результаты поиска

Содержание SpectralLED RS-7

Отзывы: