gamma scientific SpectralLED RS-7 Скачать руководство пользователя страница 67

Страница: 67 / 81

SpectralLED® RS-7 USER MANUAL

Page 66

SLM

[limit]

set soft limit to [limit] %, where [limit] is an integer between 0 and 100

Examples:

slm

query soft limit

slm80

decrease soft limit to 80%

4.6.20

- ALA - Query/reset alarms

Reports the presence of an alarm condition, or resets (clears) the alarm (if possible). A description of the various

alarms can be found in Section 4.7.2. Note that if the condition which created the alarm still exists, clearing the

alarm will cause the unit to immediately issue the alarm again. Also, alarms can be either asynchronous,

meaning that the unit will transmit the alarm string immediately when the alarm condition first arises, or polled,

in that one must issue the

ALA

command regularly to see if an alarm condition has arisen. The choice between

polled and asynchronous alarms is configured with the

ASA

command.

Syntax:

ALA

report current alarm state

ALAR

reset alarm

ALAC

clear alarm (identical to reset alarm)

Examples:

ala

query current alarm state

NONE

no alarm condition

…

?A1 – channel power limit

alarm indicating optical feedback is trying to drive a channel past 100%

ala

query alarm state

?A1 – channel power limit

alac

try to clear the alarm

?A1 – channel power limit

fault condition still exists

pre0

load preset #0

ala

query alarm state

NONE

RS-7 is properly outputting preset #0

4.6.21

- ASA - Asynchronous Alarm

This command configures whether or not an alarm condition is issued by the unit asynchronously, meaning that
it will transmit the alarm string immediately upon encountering an alarm condition. If is not desirable that the

Содержание SpectralLED RS-7


















































































Результаты поиска

Содержание SpectralLED RS-7

Отзывы:

gamma scientific SpectralLED RS-7, Руководство пользователя, Страница: 67 / 81

Результаты поиска

Содержание SpectralLED RS-7

Отзывы: