gamma scientific SpectralLED RS-7 Скачать руководство пользователя страница 39

Страница: 39 / 81

SpectralLED® RS-7 USER MANUAL

Page 38

4.2.4

- MON – Wavelength Monitor System Query

If the RS-7 is equipped with the optional Wavelength Monitor System, this command requests
centroid/peak/center wavelength (see

PTY

) and (ir)radiance of the currently active wavelength (only a single

wavelength must be active).

Syntax:

MON

query Monitor System

MON C

continuous query (ESC to terminate)

MON F

fast query, executes in under 50 ms

MON CF

continuous fast query (ESC to terminate)

Examples:

scp0,0,15,70

turn off all channels, then set channel #15 to 70% power

Ok
mon

query monitor

475.41,24.51

monitor reports wavelength of 475.41 nm, at an (ir)radiance of 24.5

4.2.5

- LIN - LED Channel Information

Reports centroid/peak/center wavelength (see

PTY

) & FWHM for each channel, in nanometers. Note that this

information is given twice; first is a nominal wavelength & FWHM representing the channel at the current

NPL

Nominal Power Level (default: 70%), and secondly the actual wavelength and FWHM for the channel’s current

operating power level, reported as 0 if the channel is set to off.

Syntax:

LIN

report all channels’ wavelength and FWHM

LIN

[chan]

report wavelength and FWHM for channel [chan]

where [chan] is an integer between 1 and 64.

Examples:

lin

report all channel’s wavelength & FWHM

1,546,11.452,545,11.521

nominal wavelength (

NPL

%), nominal FWHM, actual wavelength, actual FWHM

2,590,23.511,0,0

channel power is set to 0 (off) so actual wavelength & FWHM reported as 0,0

3,615,17.512,616,17.911

…

64,0,0,0,0

unused channels always report 0,0,0,0

final extra <CR><LF> terminates list

Содержание SpectralLED RS-7


















































































Результаты поиска

Содержание SpectralLED RS-7

Отзывы:

gamma scientific SpectralLED RS-7, Руководство пользователя, Страница: 39 / 81

Результаты поиска

Содержание SpectralLED RS-7

Отзывы: