gamma scientific SpectralLED RS-7 Скачать руководство пользователя страница 49

Страница: 49 / 81

SpectralLED® RS-7 USER MANUAL

Page 48

STS.

The data are sent from/to the RS-7 in the format specified by

STM

over the wavelength range specified by

WLR.

When sending a target spectrum to the RS-7, data points outside the

WLR

are set to 0.

Syntax:

TSP

transmit the current target spectrum to host

TSP

[data],[data],…,[data]

send target spectrum to RS-7 using

STM

TSP

[data]

send target spectrum to RS-7 using

STM

[data]

…

[data]

TSP

alternative format to send target spectrum to RS-7 using

STM

[data]

…

[data]

where [data] is an ASCII float and the number of data points is set by

WLR

([endWL] – [startWL] + 1)

Examples:

stm0

set

STM

mode 0 (not required if mode has already been set to 0)

tsp0.1941,0.298,0.4059,0.5991,…,0.09919

4.4.5

- FTS - Fit to TSP

Performs a least-squares arithmetic fit to the target spectrum

TSP

over the wavelength range

WLR

and sets the

RS-7 output

OSP

to the resultant spectrum. Only channels with wavelengths within the

WLR

+/- 5nm will be

utilized (meaning channels as far as 5nm outside

WLR

will be utilized). The addition of the

suffix to the

FTS

command will also include broadband white channels as part of the solution.

Syntax:

FTS

fit to target spectrum using only the monochromatic channels (white channels not included)

FTS W

fit to target spectrum using all channels, including white channels

FTS M

fit to target spectrum at maximum possible output power as set by

SLM

(target spectrum

TSP

will be scaled accordingly)

The RS-7 will attempt to fit the currently defined target spectrum

TSP.

Examples:

stm0

set spectral transfer mode 0

Содержание SpectralLED RS-7


















































































Результаты поиска

Содержание SpectralLED RS-7

Отзывы:

gamma scientific SpectralLED RS-7, Руководство пользователя, Страница: 49 / 81

Результаты поиска

Содержание SpectralLED RS-7

Отзывы: