gamma scientific SpectralLED RS-7 Скачать руководство пользователя страница 12

Страница: 12 / 81

SpectralLED® RS-7 USER MANUAL

Page 11

Table 1.

RS-7 System Specifications continued

Electrical Resolution

16 bit DAC for channel current drivers (32 independent DACs, 1 for each LED

channel) 24 bit ADC for internal radiance monitor/feedback

Dynamic Range

Adjustment

Spectrum dependent, 4-5 decades typical

LED Control

Pure DC constant current with floating differential sensing

Software

Firmware contains full spectral calibration, handles spectral fitting, preset storage,

real-time optical feedback, radiometric and photometric units supported.

Interface

USB 2.0 type B connector and DB-9 connector

Interface Protocol

Simple ASCII commands with optional binary block transfer

Supported Operating

Systems

USB drivers for Windows®, OSX, and Linux® via FTDI virtual COM port

Legacy RS-232 serial port for integration into automated systems (no OS required)

Input Voltage

110-240 VAC, 50-60

Maximum Power

Consumption

600

System Dimensions

Height: 405

mm, Width: 460

mm, Depth: 305

mm, Weight: 25

1. FWHM: Full-Width Half-Maximum.

2. Uniformity measured using an 8° FOV at the output plane of the device while simulating illuminant E over a wavelength range of 380

nm-1000

nm.

Uniformity spec measures over the entire Ø 75 mm active area, when considering only the center Ø 50 mm area uniformity exceeds 98%.

3. Spectra fit over a wavelength range of 380 nm-780 nm, maximum output is dependent on spectral content of the target spectra. Most CIE illuminants

and color patches can fit to at least this level, typical spectra can far exceed this maximum however some spectra cannot achieve this maximum.

4. X-Rite, Macbeth, and ColorChecker are registered trademarks of X-Rite, Inc.

Содержание SpectralLED RS-7


















































































Результаты поиска

Содержание SpectralLED RS-7

Отзывы:

gamma scientific SpectralLED RS-7, Руководство пользователя, Страница: 12 / 81

Результаты поиска

Содержание SpectralLED RS-7

Отзывы: