gamma scientific SpectralLED RS-7 Скачать руководство пользователя страница 46

Страница: 46 / 81

SpectralLED® RS-7 USER MANUAL

Page 45

4.4

Spectral Operations

4.4.1

- WLR - Set Wavelength Range

Sets or reports the operating wavelength range for spectral operations, including spectral data transfers to and

from the RS-7.

Syntax:

WLR

[startWL],[endWL]

set wavelength range [startWL] to [endWL]

WLR

report currently set wavelength range

where [startWL] and [endWL] are integers between 360 and 1100, representing nanometers, with [startWL] <

[endWL].

The wavelength range is applicable for the following commands:

OSP

Output spectrum

TSP

Target spectrum

FTS

Fit to

TSP

REP

Report RMS Error %

OSP

vs.

TSP

Examples:

wlr

report current operating wavelength range

380,780

wlr380,920

extend wavelength range to 920 nm

4.4.2

- STM - Spectrum Transfer Mode

Establishes the format for spectral data transfers between the host & RS-7. Spectral data is always 1 nm-step

resolution, units being µW/cm²/nm (irradiant source, see

CTY

IRR

) or

µW/cm²/nm/sr (radiant source, see

CTY

IRR

) and is transferred between the host and RS-7 over the wavelength range set by

WLR

Syntax:

STM

[0|1|2]

set spectral transfer mode to 0, 1, or 2

STM

report current spectral transfer mode

where spectral transfer mode 0 is comma-delimited ASCII data, spectral transfer mode 1 is <CR><LF> delimited

ASCII data (columnar), and spectral transfer mode 2 is packed binary. The packed binary format is capable of

transferring a complete set of spectral data over the full wavelength range of 380 to 1100 nm at 115,200 baud in

125 milliseconds.

When transferring in packed binary format

first an ASCII float representing a scale factor is sent

Содержание SpectralLED RS-7


















































































Результаты поиска

Содержание SpectralLED RS-7

Отзывы:

gamma scientific SpectralLED RS-7, Руководство пользователя, Страница: 46 / 81

Результаты поиска

Содержание SpectralLED RS-7

Отзывы: