gamma scientific SpectralLED RS-7 Скачать руководство пользователя страница 3

Страница: 3 / 81

SpectralLED® RS-7 USER MANUAL

Page 2

SAFETY FIRST

Protect yourself.

Follow these precautions:

•

This Manual contains information about the proper procedures for preparing this product for its use and

care.

•

Follow the instructions of other manufacturer’s equipment when used in conjunction with this product.

•

Explosion Hazard. Do not use in the presence of flammable liquids, vapors, gases or dusts.

•

FIRE HAZARD: DO NOT DRAPE OR COVER ANY LIGHT SOURCE WHILE IT IS OPERATING.

•

Pay attention to

WARNING

statements. They point out situations that can cause injury or death.

•

Pay attention to CAUTION statements. They point out situations that can cause equipment damage.

•

The user of this product should be thoroughly familiar in the set-up, use, and care of this product.

•

The user should carefully study this manual before using the equipment. Instructions should be followed,

with special attention given to warnings, controls and user specifications. This manual should be available

to the appropriate personnel.

•

Before every procedure, carefully inspect the equipment to ensure it has been properly maintained and

cleaned, and that it is fully functional. DO NOT use if inspection reveals anything unusual, including case

damage or loose connectors.

•

SAFETY PRECAUTIONS MUST ALWAYS BE EXERCISED WHEN USING ELECTRICAL EQUIPMENT TO PREVENT

OPERATOR SHOCK, FIRE HAZARD OR EQUIPMENT DAMAGE.

•

Don’t touch any exposed wiring.

•

All electrical equipment must be used with approved power cords and power plugs inserted properly into

grounded AC power outlets.

•

Don’t plug in the power cord until directed to by the installation instructions.

•

Don’t bypass the power cord’s ground lead with two-wire extension cords or plug adaptors.

•

Don’t disconnect the green and yellow safety-earth-ground wire that connects the ground lug of the power
receptacle to the chassis ground terminal (marked with or

•

To reduce the risk of fire and electric shock, do not expose electrical equipment to moisture. When

cleaning, do not immerse any electrical device in liquid.

•

Do not use or store liquids on or above the equipment.

Содержание SpectralLED RS-7


















































































Результаты поиска

Содержание SpectralLED RS-7

Отзывы:

gamma scientific SpectralLED RS-7, Руководство пользователя, Страница: 3 / 81

Результаты поиска

Содержание SpectralLED RS-7

Отзывы: