gamma scientific SpectralLED RS-7 Скачать руководство пользователя страница 56

Страница: 56 / 81

SpectralLED® RS-7 USER MANUAL

Page 55

7920.6

outa

7891.9

4.5.5

SOB - Standard observer select, 2 degree or 10 degree

Sets or reports the current CIE Tristimulus Standard Observer Included Angle as 2 degrees or 10 degrees. The

default at power-on is always 2 degrees.

Syntax:

SOB

[2|10]

set standard observer to 2 or 10 degrees

SOB

report current Standard Observer

Examples:

SOB

report current Standard Observer setting

SOB 2

change Standard Observer to 2 degrees

4.5.6

OXY - Chromaticity of OSP as CIE 1931 x,y

Reports the chromaticity of the current output spectrum

OSP

using the 2 or 10 degree Standard Observer

Included Angle as set by

SOB

Syntax:

OXY

report output spectrum

OSP

chromaticity

Returns two ASCII floats separated by a comma indicating the (x,y) coordinate on the 1931 CIE chromaticity

chart.

Examples:

sob2

select 2 degree Standard Observer (not required if 2 degree has been previously set)

oxy

report chromaticity of output spectrum

OSP

0.3333,0.3333

4.5.7

OXYZ - Tristimulus of OSP as CIE X,Y,Z

Reports the tristimulus of the current output spectrum

OSP

using the the 2 or 10 degree Standard Observer

Included Angle as set by

SOB

. Note that for 2 degree observer, the tristimulus Y value will represent the output

Содержание SpectralLED RS-7


















































































Результаты поиска

Содержание SpectralLED RS-7

Отзывы:

gamma scientific SpectralLED RS-7, Руководство пользователя, Страница: 56 / 81

Результаты поиска

Содержание SpectralLED RS-7

Отзывы: