Installation
10-004 – 676-110000
1-5
1.2.8 Water Supply and Drain Connections
(option, not applicable)
Clean water supply line shall be provided for Ultrasonic
Cleaner Dryer (UCD) system. The water filter installed
in the furnace as shipped is new, except for use in
factory testing. The furnace is shipped with a spare
water filter to be installed during startup, or as required.
Pipe water connection through rectangular opening in
lower panel Figure 1.2.13 Water Connections and Air
Purge. Supply pressure shall not exceed 100 psig.
Connect UCD drain line to accommodate maximum flow of water at 12 gpm at 40 psig.
Owner may wish to connect the condensate air purge to drain. Condensate purge may not release much
water if the air supply is sufficiently dry and the system is purged at frequent enough intervals.
See 803-091734 for connection locations and sizes.
1.2.9 Installation of the Transport Belt (applies to split chambers only – not
applicable)
A portion of the transport belt which goes through the furnace chamber was intentionally left uninstalled to
protect the furnace interior during shipment. When installing the belt, it will be helpful to have an assistant
available to help guide the belt into the furnace
entrance.
The portion of the belt which goes through the
furnace is rolled up and secured at the entrance end
of the furnace. Unroll the belt and attach it securely
to the pull wire that was left in the furnace chamber.
Pull the belt through the chamber from the exit end
of the furnace, while an assistant guides the belt into
the entrance.
Once the belt has been pulled completely through the
chamber, remove and discard the pull wire. Splice as
shown in Figure 1.2.14 Belt Splice.
1.2.10 Removal of Shipping Restraint Screws
Large furnaces operating at high temperatures experience
considerable growth from thermal expansion. All models are
equipped with support slides which allow stress free expansion to
take place. To secure the process chamber during shipment,
restraining brackets (labeled SHIPPING BRACKET) attach
directly between the chamber and frame.
Before operating the furnace first remove the top hex nuts and
washers which secure each bracket to the frame. Then remove
the bracket and discard.
Figure 1.2.13 Water Connections and Air Purge
Figure 1.2.14 Belt Splice
Figure 1.2.15 Shipping Brackets
WARNING: Failure to remove the top bracket invites
structural damage and will void the warranty.
Содержание LA-309
