Fujitsu Server PRIMERGY TX1330 M1 Скачать руководство пользователя страница 70 | Manualshive

Страница: 70 / 336

Fujitsu Server PRIMERGY TX1330 M1 Скачать руководство пользователя страница 70

70

Upgrade and Maintenance Manual

TX1330

M1

Basic software procedures

I

Administrator permission required: If you are prompted for an
administrator password or confirmation, type the password or
provide confirmation.

Ê

To temporarily disable BitLocker, click

Turn Off BitLocker

, and then click

Disable BitLocker Drive Encryption

.

I

In order to determine which features are accessible through the
BitLocker setup wizard, modify the BitLocker Group Policy settings.

For further information on how to disable BitLocker drive encryption,
please refer to the Microsoft Knowledge Base.

Fujitsu service partners will find additional information (also available
in Japanese) on the Fujitsu Extranet web pages.

5.1.2

Disabling SVOM boot watchdog functionality

The ServerView Operations Manager boot watchdog determines whether the
server boots within a preset time frame. If the watchdog timer expires, the
system will automatically reboot.

5.1.2.1

Viewing boot watchdog settings

Viewing boot watchdog settings in the BIOS

Ê

Enter the BIOS.

Ê

Select the

Server Mgmt

menu.

Ê

Under

Boot Watchdog

, you can obtain detailed information about the current

watchdog status, time out intervals and actions that are triggered if
watchdog time outs are exceeded.

I

For detailed information on BIOS settings, refer to the corresponding
BIOS Setup Utility reference manual.

Viewing boot watchdog settings in the iRMC web frontend

Ê

Enter the ServerView iRMC web frontend.

Ê

Select the

Server Management

menu.

«
...
68
69
70
71
72
...
»

Содержание Server PRIMERGY TX1330 M1

















































































































































































































































































































































Отзывы:

Нет отзывов