Fujitsu Server PRIMERGY TX1330 M1 Скачать руководство пользователя страница 187

Страница: 187 / 336

TX1330 M1

Upgrade and Maintenance Manual

187

Expansion cards and backup units

9.4.5

Replacing the TFM

9.4.5.1

Preliminary steps

"Locating the defective server" on page 43

"Disabling BitLocker functionality" on page 69

"Shutting down the server" on page 46

"Disconnecting the server from the mains" on page 46

Remove all external cables from the expansion card to be removed.

"Getting access to the component" on page 47

"Removing the fan module" on page 151

9.4.5.2

Removing the defective TFM

Remove the depending expansion card as described in section

"Removing

an expansion card" on page 180

Disconnect the FBU adapter cable as described in section

"Disconnecting

the FBU adapter cable from the TFM" on page 200

Upgrade and Repair Unit
(URU)

Hardware: 10 minutes

Tools:

Phillips PH1 / (+) No. 1 screw driver

Содержание Server PRIMERGY TX1330 M1

















































































































































































































































































































































Результаты поиска

Содержание Server PRIMERGY TX1330 M1

Отзывы:

Fujitsu Server PRIMERGY TX1330 M1, Руководство по модернизации и обслуживанию, Страница: 187 / 336

Результаты поиска

Содержание Server PRIMERGY TX1330 M1

Отзывы: