Fujitsu Server PRIMERGY TX1330 M1 Скачать руководство пользователя страница 212

Страница: 212 / 336

212

Upgrade and Maintenance Manual

TX1330

Main memory

10.2.2 Removing a memory module

Identify the desired memory slot see section

"Memory sequence" on

page 210

CAUTION!

Ensure to maintain an operational configuration when removing
memory modules. For additional information, please refer to section

"Basic information" on page 209

Figure 123: Removing memory modules

Eject the desired memory module by pressing out the securing clips at each
end of the memory slot (1).

Remove the ejected memory module (2).

10.2.3 Concluding steps

"Installing the fan module" on page 152

"Reassembling" on page 58

"Connecting the server to the mains" on page 67

"Switching on the server" on page 68

If applicable,

"Updating or recovering the system board BIOS and iRMC" on

page 76

"Enabling SVOM boot watchdog functionality" on page 84

"Enabling BitLocker functionality" on page 90

Содержание Server PRIMERGY TX1330 M1

















































































































































































































































































































































Результаты поиска

Содержание Server PRIMERGY TX1330 M1

Отзывы:

Fujitsu Server PRIMERGY TX1330 M1, Руководство по модернизации и обслуживанию, Страница: 212 / 336

Результаты поиска

Содержание Server PRIMERGY TX1330 M1

Отзывы: