manualshive.com logo in svg

Fujitsu Server PRIMERGY TX1330 M1, Руководство по модернизации и обслуживанию, Страница: 116 / 336

Поделиться
Скачать
Fujitsu Server PRIMERGY TX1330 M1 Скачать руководство пользователя страница 116

116

Upgrade and Maintenance Manual

 TX1330 

M1

Power supply

6.3.4.5

Concluding steps

Ê

"Installing the fan module" on page 152

Ê

"Reassembling" on page 58

Ê

"Connecting the server to the mains" on page 67

Ê

"Switching on the server" on page 68

Ê

"Enabling BitLocker functionality" on page 90

6.4

Converting a standard power supply to a 
redundant power supply

The standard power supply can be replaced by a redundant power supply. The 
redundant power supply consists of up to two power supply units (slide-in units). 
The upgrade kit contains only one power supply unit (for power supply 
redundancy the second power supply unit must be additionally ordered).

The upgrade kit for the redundant power supply consists of the following parts:
– PSU cage with power distribution board (incl.power cables)
– one hot-plug power supply unit
– dummy cover (if only one power supply unit is installed, you have to install 

the dummy cover in the second bay)

– several screws

6.4.1

Preliminary steps

Ê

"Disabling BitLocker functionality" on page 69

Ê

"Shutting down the server" on page 46

Ê

"Disconnecting the server from the mains" on page 46

Ê

"Getting access to the component" on page 47

Ê

"Removing the fan module" on page 151

Field Replaceable Unit
(FRU)

Hardware: 10 minutes

Tools:

Phillips PH2 / (+) No. 2 screw driver

Содержание Server PRIMERGY TX1330 M1

















































































































































































































































































































































Отзывы:

Нет отзывов