manualshive.com logo in svg

Fujitsu Server PRIMERGY TX1330 M1, Руководство по модернизации и обслуживанию, Страница: 302 / 336

Поделиться
Скачать
Fujitsu Server PRIMERGY TX1330 M1 Скачать руководство пользователя страница 302

302

Upgrade and Maintenance Manual

 TX1330 

M1

Cabling

16.1 List of used cables

I

The numbers in the cable list correspond to those shown in the cabling 
plans.

No. Name

Cable number

Routing

1

Front panel module 
cable

T26139-Y4015-V301

from front panel module to system 
board

2

Front / internal USB 
cable

T26139-Y3999-V504

from front panel module / USB 3.0 
backup drive to system board

3

Intrusion switch cable T26139-Y3922-V121 from server front to system board

4

HDD / ODD power 
cable

T26139-Y4012-V502

from HDD backplanes and accessible 
drives to system board

5

ODD SATA cable

T26139-Y3928-V205 from optical disk drive to system board

6

HDD SAS cable

T26139-Y3963-V103

from HDD backplane to SAS controller 
or system board 

7

Hot-Plug PSU power 
cable

T26139-Y3952-V611

from power distribution board to 
system board

8

Power supply unit 
signal cable

T26139-Y3956-V2

from power distribution board to 
system board

9

If FBU installed: 
FBU adapter cable

T26139-Y4032-V3

from FBU module to SAS controller

10

If BBU installed:
BBU cable

T26139-Y3987-V3

from BBU module to SAS controller

11

PCI riser card power 
cable

T26139-Y4029-V202 from PCI riser card to HDD backplane

12

SAS backup drive 
power / data cable

T26139-Y3969-V401

from SAS backup drive to system 
board or SAS backup controller

13

Internal USB to 5-pin 
cable

T26139-Y3973-V2

from internal USB backup drive to 
system board 

Table 8: List of used cables

Содержание Server PRIMERGY TX1330 M1

















































































































































































































































































































































Отзывы:

Нет отзывов