Fujitsu Server PRIMERGY TX1330 M1 Скачать руководство пользователя страница 60

Страница: 60 / 336

Upgrade and Maintenance Manual

TX1330

Basic hardware procedures

4.5.1.3

Mounting the server in the rack

CAUTION!

At least two people are needed to position the server on the rack rails.
(For the Japanese market, please refer to "

安全上のご注意

".)

Additionally, a lifter is required in the following cases:

– The server weighs more than 50 kg.
– The server weighs more than 21 kg and is to be installed above the

height of 25 U.

When using a lifter, this installation procedure needs to be carried out by
maintenance personnel.

For configurations below 32 kg:

At least two people are needed to lift the server
into the rack cabinet.

For configurations below 55 kg:

At least three people are needed to lift the server
into the rack cabinet.

For configurations above 55 kg:

At least four people are needed to lift the server
into the rack cabinet.

Содержание Server PRIMERGY TX1330 M1

















































































































































































































































































































































Результаты поиска

Содержание Server PRIMERGY TX1330 M1

Отзывы:

Похожие инструкции для Server PRIMERGY TX1330 M1

Бренды по названию

Популярные бренды

Fujitsu Server PRIMERGY TX1330 M1, Руководство по модернизации и обслуживанию

Результаты поиска

Содержание Server PRIMERGY TX1330 M1

Отзывы:

Похожие инструкции для Server PRIMERGY TX1330 M1

Бренды по названию

Популярные бренды