Fujitsu MHU2100AT Скачать руководство пользователя страница 164 | Manualshive

Страница: 164 / 278

background image

Interface

5-88 C141-E202-01EN

(30) SET FEATURES (X’EF’)

The host system issues the SET FEATURES command to set parameters in the
Features register for the purpose of changing the device features to be executed.

Upon receipt of this command, the device sets the BSY bit of the Status register
and saves the parameters in the Features register. Then, the device clears the BSY
bit, and generates an interrupt.

If the value in the Features register is not supported or it is invalid, the device
posts an ABORTED COMMAND error.

Table 5.23 lists the available values and operational modes that may be set in the
Features register.

Table 5.23 Features register values and settable modes

Features
Register

Drive operation mode

X’02’

Enables the write cache function.

X’03’

Set the data transfer mode. *1

X’05’

Enables the advanced power management function. *2

X’42’

Enables the Acoustic management function. *3

X’55’

Disables read cache function.

X’66’

Disables the reverting to power-on default settings after software reset. (*1)

X’82’

Disables the write cache function.

X’85’

Set the advanced power management mode to Mode-0.

X’AA’

Enables the read cache function.

X’BB’

Specifies the transfer of 4-byte ECC for READ LONG and WRITE LONG
commands. (*1)

X’C2’

Disables the Acoustic management function.

X’CC’

Enables the reverting to power-on default settings after software reset. (*1)

*1 Although there is a response to the command, nothing is done.

At power-on or after hardware reset, the default mode is set as follows.

Write cashe function

: Enabled

Transfer mode

: PIO Mode-4, Multiworld DMA Mode-2

Advanced

power

management function

: Enabled (Mode-1)

Acoustic
management function

: State keeping

Read cashe function

: Enabled

«
...
162
163
164
165
166
...
»

Содержание MHU2100AT























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MHU2100AT

Бренд: Eastwood Страницы: 8

Бренд: Feider Machines Страницы: 20

Бренд: LaCie Страницы: 28

OMNISTOR 4000f SERIES

Бренд: Rackable Systems Страницы: 112

Бренд: IBM Страницы: 314

Бренд: Raidon Страницы: 2

Бренд: Husky Страницы: 10

Бренд: morse Страницы: 7

Universal Bench

Бренд: Kreg Страницы: 12

Бренд: Asus Страницы: 32

Бренд: Asus Страницы: 40

Бренд: Asus Страницы: 58

Бренд: Asus Страницы: 10

Бренд: Asus Страницы: 8

Leather External HDD USB 3.0

Бренд: Asus Страницы: 2

Бренд: Asus Страницы: 14

Бренд: Asus Страницы: 21

AN200 External HDD

Бренд: Asus Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды