Fujitsu MHU2100AT Скачать руководство пользователя страница 249 | Manualshive

Страница: 249 / 278

background image

6.3 Defect Processing

C141-E202-01EN 6-11

(3) Automatic alternating processing

This technology assigns a defective sector to a spare sector of an spare cylinder
for alternate assignment.

This device performs automatic alternating processing in the event of any of the
following errors.

•

Automatic alternating processing is attempted for read error recovery by
reaching the specified retry cycle while a read error retry is in progress.

Before attempting automatic alternating processing, writing and reading of
already corrected data is repeated for the sector in which an error occurred. If
a read error does not occur during this reading operation, automatic
alternating processing is not performed.

•

If error recovery is not successful even if a write fault error retry is executed,
automatic alternating processing is performed.

Figure 6.6 shows an example where automatic alternating processing is applied to
sector (physical) 5 with cylinder 0 and head 0.

Sector (physical)

Cylinder 0
Head 0

Defec-
tive
sector

(Not used)

Alternate cylinder 0
Head 0

This is assigned to an unassigned sector.

Already
assigned

779 780

779 780

Notes:

1. The alternate cylinder is assigned to an inner cylinder in each zone.

2. When an access request for sector 5 is issued, the sector assigned for

alternating processing of the alternate cylinder must be accessed instead of
physical sector 5.

If an access request for sectors after sector 5 is issued, seek is executed to
cylinder 0, head 0 in order to continue processing.

Figure 6.6 Automatic alternating processing

«
...
247
248
249
250
251
...
»

Содержание MHU2100AT























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MHU2100AT

G-DRIVE mobile USB

Бренд: G-Technology Страницы: 13

Бренд: PaloAlto Networks Страницы: 2

Spectra 2K Library

Бренд: Spectra Logic Страницы: 93

Бренд: Seville Classics Страницы: 7

G2 R8000 3U WW ERM

Бренд: HPE Страницы: 3

Бренд: AIC Страницы: 105

Бренд: Quantum Страницы: 20

Бренд: Glyph Страницы: 2

Бренд: LaCie Страницы: 24

Maxtor OneTouch 4

Бренд: Maxtor Страницы: 84

TotalStorage NAS 100

Бренд: IBM Страницы: 18

MediaLounge DSM-602H

Бренд: D-Link Страницы: 12

SharePort DNS-323

Бренд: D-Link Страницы: 17

Бренд: D-Link Страницы: 46

MediaLounge DSM-622H

Бренд: D-Link Страницы: 16

MediaLounge DSM-622H

Бренд: D-Link Страницы: 46

MediaLounge DSM-602H

Бренд: D-Link Страницы: 39

ShareCenter 2Go - DNS-213

Бренд: D-Link Страницы: 87

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды