Fujitsu MHU2100AT Скачать руководство пользователя страница 220 | Manualshive

Страница: 220 / 278

background image

Interface

5-144 C141-E202-01EN

13) The host shall neither negate STOP nor HSTROBE until at least t

ACK

after

negating DMACK-.

14) The host shall not assert DIOW-, CS0-, CS1-, DA2, DA1, or DA0 until

at least t

ACK

after negating DMACK.

5.5.5 Ultra DMA CRC rules

The following is a list of rules for calculating CRC, determining if a CRC error
has occurred during an Ultra DMA burst, and reporting any error that occurs at
the end of a command.

a) Both the host and the device shall have a 16-bit CRC calculation function.

b) Both the host and the device shall calculate a CRC value for each Ultra DMA

burst.

c) The CRC function in the host and the device shall be initialized with a seed of

4ABAh at the beginning of an Ultra DMA burst before any data is
transferred.

d) For each STROBE transition used for data transfer, both the host and the

device shall calculate a new CRC value by applying the CRC polynomial to
the current value of their individual CRC functions and the word being
transferred. CRC is not calculated for the return of STROBE to the asserted
state after the Ultra DMA burst termination request has been acknowledged.

e) At the end of any Ultra DMA burst the host shall send the results of its CRC

calculation function to the device on DD (15:0) with the negation of
DMACK-.

f) The device shall then compare the CRC data from the host with the calculated

value in its own CRC calculation function. If the two values do not match,
the device shall save the error and report it at the end of the command. A
subsequent Ultra DMA burst for the same command that does not have a
CRC error shall not clear an error saved from a previous Ultra DMa burst in
the same command. If a miscompare error occurs during one or more Ultra
DMA bursts for any one command, at the end of the command, the device
shall report the first error that occurred.

g) For READ DMA or WRITE DMA commands: When a CRC error is

detected, it shall be reported by setting both ICRC and ABRT (bit 7 and bit 2
in the Error register) to one. ICRC is defined as the "Interface CRC Error"
bit. The host shall respond to this error by re-issuing the command.

h) A host may send extra data words on the last Ultra DMA burst of a data out

command. If a device determines that all data has been transferred for a
command, the device shall terminate the burst. A device may have already
received more data words than were required for the command. These extra
words are used by both the host and the device to calculate the CRC, but, on
an Ultra DMA data out burst, the extra words shall be discarded by the
device.

«
...
218
219
220
221
222
...
»

Содержание MHU2100AT























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MHU2100AT

BLACKOUT WINDOW STORAGE SYSTEM

Бренд: REBEL OFF ROAD Страницы: 9

Бренд: oldfields Treco Страницы: 36

Cheetah 15K.7 SAS ST3300557SS

Бренд: Seagate Страницы: 76

Бренд: PARYA Страницы: 6

Бренд: LaCie Страницы: 27

Бренд: Extreme Tools Страницы: 2

Бренд: U-Line Страницы: 6

SLR AUTOLOADER PROGRAMMER

Бренд: Tandberg Data Страницы: 62

System Storage DCS Series

Бренд: IBM Страницы: 90

XCubeNAS XN3002T

Бренд: Qsan Страницы: 12

Бренд: P.V. Supa Страницы: 54

Бренд: Maxtor Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

HEART WARE FM01SW20

Бренд: Philips Страницы: 2

Lock In FM01SW60

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды