Fujitsu MHU2100AT Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 278

background image

Device Overview

1-12 C141-E202-01EN

Emergency Unload other than Normal Unload is performed when the power is
shut down while the heads are still loaded on the disk.
The product supports the Emergency Unload a minimum of 20,000 times.
When the power is shut down, the controlled Normal Unload cannot be executed.
Therefore, the number of Emergency other than Normal Unload is specified.

Remark:

We recommend cutting the power supply of the HDD for this device after the
Head Unload operation completes. The recommended power supply cutting
sequence for this device is as follows:

1) Disk

Flush

Flush Cache command execution.

2) Head

Unload

Standby Immediate command execution.

3) Wait

Status

Checking whether bit 7 of the status register was set to '0'.
(wait to complete STANDBY IMMEDIATE command)

4) HDD power supply cutting

1.11 Advanced Power Management

The disk drive automatically shifts to the power saving mode according to the
setting of the APM mode under the idle condition.

The APM mode can be chosen with a Sector Count register of the SET
FEATURES(EF) command.

The disk drive complies with the three kinds of APM modes that a command
from the host is required.

FR = 05h : Enable APM

SC = C0h - FEh :

Mode-0 Active Idle

→

Low Power Idle

SC = 80h - BFh :

Mode-1 Active Idle

→

Low Power Idle (Default)

SC = 01h - 7Fh :

Mode-2 Active Idle

→

Low Power Idle

→

Standby

FR = 85h : Disable APM (Set Mode-0)

Active Idle:

The head is in a position of extreme inner in disk
medium. (VCM Lock)

Low Power Idle:

The head is unloaded from disk.
The spindle motor rotates.

«
...
34
35
36
37
38
...
»

Содержание MHU2100AT























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MHU2100AT

FlashSystem 710

Бренд: IBM Страницы: 46

Бренд: IBM Страницы: 8

Бренд: IBM Страницы: 202

DARA-206000 - Travelstar 12 GB Hard Drive

Бренд: IBM Страницы: 206

BladeCenter S 7779

Бренд: IBM Страницы: 28

DSN-3200 - xStack Storage Area Network Array Hard...

Бренд: D-Link Страницы: 7

GLADIATOR PLUS 2

Бренд: Asgard Страницы: 6

Бренд: DataWhale Страницы: 31

Бренд: Quantum Страницы: 78

Бренд: Extreme Tools Страницы: 2

Бренд: Oki Страницы: 16

Бренд: DEC Страницы: 94

Бренд: Mercia Garden Products Страницы: 9

Бренд: Eneo Страницы: 12

Бренд: Canon Страницы: 76

TIGERFLEX SHIPLAP APEX BIKE SHED

Бренд: Tiger Страницы: 16

Бренд: StorageTek Страницы: 86

Бренд: Extraflame Страницы: 112

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды