manualshive.com logo in svg

Fujitsu MHU2100AT, Руководство по эксплуатации продукта

"Загрузите Installation Manual для Fujitsu MHU2100AT бесплатно на нашем сайте. Manual содержит подробные инструкции по установке продукта. Не забудьте загрузить его с manualshive.com для получения всей необходимой информации о этом товаре."

Поделиться
Скачать
background image

5.2  Logical Interface

 

C141-E202-01EN 5-9 

 

- Bit 1: 

Track 0 Not Found (TK0NF).  This bit indicates that track 0 was not 
found during RECALIBRATE command execution. 

- Bit 0: 

Address Mark Not Found (AMNF).  This bit indicates that the SB Not 
Found error occurred. 

 

[Diagnostic code] 

 

X’01’: 

No Error Detected. 

X’02’: 

HDC Diagnostic Error 

X’03’: 

Data Buffer Diagnostic Error. 

X’04’: 

Memory Diagnostic Error. 

X’05’: 

Reading the system area is abnormal. 

X’06’: 

Calibration is abnormal. 

X’80’: 

Device 1 (slave device) Failed. 

Error register of the master device is valid under two devices (master 
and slave) configuration. If the slave device fails, the master device 
posts X’80’ OR (the diagnostic code) with its own status (X’01’ to 
X’06’). 

However, when the host system selects the slave device, the diagnostic 
code of the slave device is posted. 

 

(3)  Features register (X’1F1’)  

The Features register provides specific feature to a command. For instance, it is 
used with SET FEATURES command to enable or disable caching. 

(4)  Sector Count register (X’1F2’)  

The Sector Count register indicates the number of sectors of data to be transferred 
in a read or write operation between the host system and the device.  When the 
value in this register is X’00’, the sector count is 256.  With the EXT system 
command, the sector count is 65536 when value of this register is X'00' in the first 
setting and X'00' in the second setting. 

When this register indicates X’00’ at the completion of the command execution, 
this indicates that the command is completed successfully.  If the command is not 
completed successfully, this register indicates the number of sectors to be 
transferred to complete the request from the host system.  That is, this register 
indicates the number of remaining sectors that the data has not been transferred 
due to the error. 

The contents of this register has other definition for the following commands;  
INITIALIZE DEVICE PARAMETERS, SET FEATURES, IDLE, STANDBY and 
SET MULTIPLE MODE. 

Содержание MHU2100AT























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MHU2100AT

DB GROUP HERRAJES 803 Assembly Instruction preview
803
Бренд: DB GROUP HERRAJES Страницы: 4
NEC Built-In AIT User Manual preview
Built-In AIT
Бренд: NEC Страницы: 59
IAC INDUSTRIES 960 Quick Start Manual preview
960
Бренд: IAC INDUSTRIES Страницы: 9
Ice-O-Matic B100 Service & Parts Manual preview
B100
Бренд: Ice-O-Matic Страницы: 9
G-Technology G-DRIVE mini Installation Manual preview
G-DRIVE mini
Бренд: G-Technology Страницы: 13
LaCie Mobile Drive Manual preview
Mobile Drive
Бренд: LaCie Страницы: 25
SanDisk SSD Ultra ATA Specification & User Manual preview
SSD Ultra ATA
Бренд: SanDisk Страницы: 44
IBM BladeCenter Management Module Installation Manual preview
BladeCenter Management Module
Бренд: IBM Страницы: 82
QNAP TS-464U User Manual preview
TS-464U
Бренд: QNAP Страницы: 69
Extreme Tools EX7215CH Assembly Instructions preview
EX7215CH
Бренд: Extreme Tools Страницы: 2
ATI Technologies SX160 Manual Installation, Use And Maintenance preview
SX160
Бренд: ATI Technologies Страницы: 24
IBM 10/20 GB TR-5 User Manual preview
10/20 GB TR-5
Бренд: IBM Страницы: 36
Argus SD-0512 Specification Sheet preview
SD-0512
Бренд: Argus Страницы: 1
Kvaser Memorator Pro 5xHS User Manual preview
Memorator Pro 5xHS
Бренд: Kvaser Страницы: 27
Buffalo MiniStation HD-PFU2 Series Quick Setup Manual preview
MiniStation HD-PFU2 Series
Бренд: Buffalo Страницы: 94
Infotrend EonStor DS B Series Hardware Manual preview
EonStor DS B Series
Бренд: Infotrend Страницы: 157
Hitachi HTS541680J9SA00 - Travelstar 80 GB Hard Drive Specifications preview
HTS541680J9SA00 - Travelstar 80 GB Hard Drive
Бренд: Hitachi Страницы: 167
Hitachi HTS541616J9AT00 - Travelstar 160 GB Hard Drive Install Manual preview
HTS541616J9AT00 - Travelstar 160 GB Hard Drive
Бренд: Hitachi Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды