Fujitsu General ASHG07KPCE Скачать руководство пользователя | Manualshive

Страница: 118 / 132

background image

7-3. Forced cooling operation

The outdoor unit may not operate depending on the room temperature.
When FORCED COOLING OPERATION button is pressed more than 10 seconds, forced cooling
operation starts as shown in the table below.

Operation mode

Cooling

Fan mode

HIGH

Timer mode

Continuous (no timer setting available)

Setting temperature

24°C

Vertical airflow direction louver setting

Standard

Horizontal airflow direction louver setting

According to memory position

SWING

Off

ECONOMY

Off

Human sensor

Off

• During the forced cooling operation, it operates regardless of room temperature sensor.
• The operation indicator lamp and the timer indicator lamp blink simultaneously during the forced

cooling operation.
They blink for 1 second ON and 1 second OFF on both the operation indicator lamp and the timer
indicator lamp (same as test operation).

By performing one of the following action, test operation will be canceled:

• Pressing the remote controller START/STOP button
• Pressing FORCED COOLING OPERATION button for 3 seconds
• 60 minutes passed after starting forced cooling operation

NOTE:

When HEAT operation is selected on the remote controller during forced cooling operation,
heating test run will begin in about 3 minutes.

7-4. ECONOMY operation

The ECONOMY operation starts by pressing ECONOMY button on the remote controller.
The ECONOMY operation is almost the same operation as below settings.

Mode

Cooling/Dry

Heating

Target temperature

Setting tempe1°C

Setting temperature -1°C

7-5. POWERFUL operation

The POWERFUL operation starts by pressing POWERFUL button on the remote controller.
The indoor unit and outdoor unit operate at maximum power as shown in the table below.

Rotation number of compressor

Maximum

Fan mode

POWERFUL

Vertical airflow direction
louver setting

Cooling

3

Dry
Heating

6

Release condition:

• Cooling/Dry

Room temperature ≤ Setting temperature -0.5°C or Operation time has passed 20 minutes.

• Heating

Room temperature ≥ Setting tempe0.5°C or Operation time has passed 20 minutes.

7-3. Forced cooling operation

- (04-24) -

7. Various control

CONTROL AND

FUNCTIONS

CONTROL AND

FUNCTIONS

«
...
116
117
118
119
120
...
»

Содержание General ASHG07KPCE





































































































































Отзывы:

Нет отзывов

Похожие инструкции для General ASHG07KPCE

HWR05XC6 - 5200 BTU Electronic Control Room Air...

Бренд: Haier Страницы: 20

Бренд: CLIVET Страницы: 64

Бренд: Kelvinator Страницы: 16

Бренд: King Industrial Страницы: 6

Бренд: Salton Страницы: 12

Бренд: mundoclima Страницы: 26

Бренд: Daikin Страницы: 6

Бренд: Odorox Страницы: 12

V7KI-18WiFiR/U7RS-18

Бренд: INVENTOR Страницы: 144

Бренд: Airtecnics Страницы: 22

Therapure TP250

Бренд: Boneco Страницы: 32

Бренд: Daikin Страницы: 10

Бренд: EWM Страницы: 26

Бренд: Lennox Страницы: 28

Бренд: Daikin Страницы: 40

Бренд: Daikin Страницы: 44

Бренд: Panasonic Страницы: 66

Бренд: Panasonic Страницы: 66

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды