Fujitsu Siemens Computers PRIMERGY RX100 S4 Скачать руководство пользователя страница 121

Страница: 121 / 285

121

PRIMERGY RX100 S4 User’s Guide

Manu

al O

allation

4.2.3 Installing Windows 2000 Server

Create driver disks.

Prepare necessary drivers before installing Windows 2000 Server.

Some drivers used with Windows 2000 Server are created from the ServerStart CD-ROM. For

how to create driver disks, refer to "4.1 Creating Driver Disks" (

pg.110).

Turn on the server and configure RAID. If RAID is not required to be configured,

proceed to step 3.

Turn on the server to display the following message and press the [Ctrl] + [C] key to start up the

RAID BIOS Utility.

Configure RAID 1. For more details, refer to "Integrated Mirroring SAS User’s Guide" in the

Array Controller Document & Tool CD.

Turn off the server after configuring the array system.

Prepare the Windows 2000 Server CD-ROM.

Insert the created driver disk. Then turn on the server and insert the Windows 2000 Server CD-

ROM immediately into the CD-ROM drive. When the active area is specified on the hard disk,

the following message appears.

Pressing any key while this message is displayed boots the system from the CD-ROM.

The Windows 2000 Server setup window appears.

Immediately, the following message appears at the bottom of the window. Press the [F6] key.

This message will be displayed for a short time after the setup window (blue screen) appears.
Press the [F6] key immediately after the window turns blue.

Install the drivers for the array controller manually.

1. When the following message appears, press the [S] key.

Press Ctrl-C to start LSI Logic Configuration Utility

Press any key to boot from CD....

Press F6 if you need to install a third party SCSI or RAID

driver ...

To specify additional SCSI adapters, CD-ROM drives, or

special disk controllers for use with Windows 2000,

including those for which you have a device support disk

from a mass storage device manufacturer, press S.

Содержание PRIMERGY RX100 S4






























































































































































































































































































Результаты поиска

Содержание PRIMERGY RX100 S4

Отзывы:

Бренды по названию

Популярные бренды

Fujitsu Siemens Computers PRIMERGY RX100 S4, Руководство пользователя

Результаты поиска

Содержание PRIMERGY RX100 S4

Отзывы:

Бренды по названию

Популярные бренды