Fujitsu Siemens Computers PRIMERGY RX100 S4 Скачать руководство пользователя страница 118

Страница: 118 / 285

118

Chapter 4 Manual OS Installation

4.2.2 Installing Windows Server 2003

For details on the OS settings, refer to the following URL.

http://www.microsoft.com/technet/prodtechnol/exchange/2003/Library/default.mspx

Create driver disks.

Prepare necessary drivers before installing Windows Server 2003.

Some drivers are created from the ServerStart CD-ROM.

For how to create driver disks, refer to "4.1 Creating Driver Disks" (

pg.110).

Turn on the server and configure RAID. If RAID is not required to be configured,

proceed to step 3.

Turn on the server, and when the following message is displayed, press the [Ctrl] + [C] key to

start up the RAID BIOS Utility.

Configure RAID 1. For more details, refer to "Integrated Mirroring SAS User’s Guide" in the

Array Controller Document & Tool CD.

Turn off the server after configuring the array system.

Prepare the Windows Server 2003 CD-ROM.

Insert the created driver disk. Then turn on the server and insert the Windows Server 2003 CD-

ROM immediately into the CD-ROM drive. When the active area is specified on the hard disk,

the following message appears.

Pressing any key while this message is displayed boots the system from the CD-ROM.

The Windows Server 2003 setup window appears.

Immediately, the following message appears at the bottom of the window. Press the [F6] key.

This message will be displayed for a short time after the setup window (blue screen) appears.
Press the [F6] key immediately after the window turns blue.

Install the Drivers for the array controller manually.

1. When the following message appears, press the [S] key.

Press Ctrl-C to start LSI Logic Configuration Utility

Press any key to boot from CD....

Press F6 if you need to install a third party SCSI or RAID

driver ...

To specify additional SCSI adapters, CD-ROM drives, or

special disk controllers for use with Windows, including

those for which you have a devicesupport disk from a mass

storage device manufacturer, press S.

Содержание PRIMERGY RX100 S4






























































































































































































































































































Результаты поиска

Содержание PRIMERGY RX100 S4

Отзывы:

Бренды по названию

Популярные бренды

Fujitsu Siemens Computers PRIMERGY RX100 S4, Руководство пользователя

Результаты поиска

Содержание PRIMERGY RX100 S4

Отзывы:

Бренды по названию

Популярные бренды