FUJIPLA AL-MEISTER ALM3230 Скачать руководство пользователя | Manualshive

Страница: 50 / 68

background image

DryLam

A Trademark of Martin Yale Industries

251 Wedcor Avenue, Wabash, IN 46992

Brian Jennett- Tech-Line & Service Advisor/Manager

Phone: (260-569-7231)

ALM3230 Customer Instruction Manual.docx

Page 50 of 68

5. AUTOMATIC OPERATION (cont’d)

5-2-9. PAPER FEED ADJUST (SOFTWARE)

PAPER FEED ADJUST is a parameter that adjusts the aggressiveness of the feeding section to enhance

compatibility of varying paper stocks. This should be utilized in conjunction with the Paper Feed Resist

Roller Pressure Adjust (MECHANICAL) knob under the Feed Tray (see

).

1. Press MODE and use the arrow buttons to select PAPER FEED ADJUST parameter. Press MODE again.

---- PAPER FEED ADJUST ----

VALUE: 10

2. Adjust the value using the up and down arrows. The factory default is 0. The range is:

Ver 1

+20 to -20 in increments of 1

If paper/toner is difficult to separate and feed use a more positive (higher) value. This will run the feeder
a longer amount of time after the leading edge of paper has passed the Feeder Sensor. Use a more
positive value in cases where paper does not reach the film in time (and “LAMINATION ERROR” errors
result).
If paper is very easy to separate and feed use a more negative (lower) value. This will make the Feeder
less aggressive. A lower value should be used if:

•

Certain lamination defects occur including, but not limited to, jamming of the leading edge of
paper occurs at the film. This might be seen as any, or part of the leading edge of a sheet paper
folded over within the film.

•

Frequent “PAPER JAM” errors occur.

•

Skewing of paper is observed occurring on the paper tray.

«
...
48
49
50
51
52
...
»

Содержание AL-MEISTER ALM3230





































































Отзывы:

Нет отзывов

Похожие инструкции для AL-MEISTER ALM3230

Бренд: Olympia Страницы: 86

script OL 250-Q125

Бренд: ALDI Страницы: 21

Бренд: Peach Страницы: 17

Scotch PRO TL1306

Бренд: 3M Страницы: 6

Бренд: UNITED OFFICE Страницы: 51

Бренд: Nuova Страницы: 10

Бренд: Nuova Страницы: 10

Бренд: Mega Electronics Страницы: 15

Бренд: Peak Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды