FUJIPLA AL-MEISTER ALM3230 Скачать руководство пользователя | Manualshive

Страница: 53 / 68

background image

DryLam

A Trademark of Martin Yale Industries

251 Wedcor Avenue, Wabash, IN 46992

Brian Jennett- Tech-Line & Service Advisor/Manager

Phone: (260-569-7231)

ALM3230 Customer Instruction Manual.docx

Page 53 of 68

5. AUTOMATIC OPERATION (cont’d)

5-2-12. PAPER FEED RESIST ROLLER PRESSURE ADJUSTMENT (MECHANICAL)

PROCEDURE:

1.

Remove the Paper Feed Resist Roller Pressure Adjust Lever and place it in the appropriate slot of
the paper and print being laminated.

2.

Always adjust in 1 step increments (or, about one mark at a time on appropriate labels) as
follows:

a.

If too many sheets are being fed at once loosen and slide the knob downward.

b.

If sheets are slow to enter, or will not enter at all (enough that “LAMINATION ERROR”,
or other similar errors occur) loosen and slide the knob upward.

HINT: Try small adjustments 1 step at a time until the optimum setting is found for the paper stock being
laminated. This adjustment should be performed in conjunction with the Paper Feed Adjust (Software)
parameter in the menu.

See section 5-2-8

for more details.

HINT: When “Lamination Error” and “Feeder Error” appear frequently adjust this knob downward
slightly (in small 1/8” increments). For best results use this adjustment along with the Paper Feed Adjust
parameter in the Mode Menu.
HINT: This is a compatibility adjustment. There is no “perfect” or “standard” setting. Different paper
stocks and toners will have different characteristics. Experimentation is key. It is better to have the

«
...
51
52
53
54
55
...
»

Содержание AL-MEISTER ALM3230





































































Отзывы:

Нет отзывов

Похожие инструкции для AL-MEISTER ALM3230

KH 4418 LAMINATOR

Бренд: UNITED OFFICE Страницы: 51

Бренд: UNITED OFFICE Страницы: 51

Бренд: Royal Sovereign Страницы: 12

Бренд: Mefu Страницы: 11

Бренд: Mefu Страницы: 11

Бренд: Bonsaii Страницы: 32

Бренд: Aveli Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды