FUJIPLA AL-MEISTER ALM3230 Скачать руководство пользователя

Страница: 20 / 68

DryLam

A Trademark of Martin Yale Industries

251 Wedcor Avenue, Wabash, IN 46992

Brian Jennett- Tech-Line & Service Advisor/Manager

Phone: (260-569-7231)

www.DryLam.com

ALM3230 Customer Instruction Manual.docx

Page 20 of 68

To feed forward, turn the switch to left.

To feed backward, turn the switch to right.

* Set the trimmer adjuster to Film Set position during the threading process.

The MOVE switch will not operate after some errors (See

#7. TROUBLESHOOTING/ERROR MESSAGES

Manual CUT Switch

Use when setting film or cutting film which is stuck in the laminator. *It does not work when a cutting error

has occurred.

2. NAMES AND FUNCTION (cont’d)

NOTE: The manual MOVE switch works most any time during manual mode. Some errors it may be necessary

to press RESET to clear the error which will then restore the MOVE switch function.

Other errors (often accompanied by the words “CALL FOR SERVICE”) require the ALM3230 to be powered off

and turned on again to restore operation.

CAUTION:

Whenever using the MOVE switch it is important to account for all film going into the machine,

particularly during the threading process. If film does not exit the discharge in less than 5 seconds

STOP!

Film

may be accumulating within the machine. If this is allowed to continue, damage to interior components of the

machine will occur.

*If you believe an excess amount of film has gone into the machine release the MOVE switch. Raise the

Lamination Handle and pull the film back out the front of the lamination area. Use the MOVE switch to assist,

if necessary.

*Whenever you use the manual MOVE Switch, even for a brief moment, always move enough film out the

discharge to grab on to. Then, always cut the film by using the manual CUT button and pull the cut film/paper

from the discharge. This must be performed before pressing the START button, otherwise errors and/or

damage to the machine may result.

*After the film waste has been pulled from the discharge the machine is ready to be run in automatic mode.

Do NOT run the MOVE switch again unless CUT is performed immediately afterward.

Содержание AL-MEISTER ALM3230





































































Результаты поиска

Содержание AL-MEISTER ALM3230

Отзывы:

Похожие инструкции для AL-MEISTER ALM3230

Бренды по названию

Популярные бренды

FUJIPLA AL-MEISTER ALM3230, Инструкция по эксплуатации

Результаты поиска

Содержание AL-MEISTER ALM3230

Отзывы:

Похожие инструкции для AL-MEISTER ALM3230

Бренды по названию

Популярные бренды