FUJIPLA AL-MEISTER ALM3230 Скачать руководство пользователя

Страница: 33 / 68

DryLam

A Trademark of Martin Yale Industries

251 Wedcor Avenue, Wabash, IN 46992

Brian Jennett- Tech-Line & Service Advisor/Manager

Phone: (260-569-7231)

www.DryLam.com

ALM3230 Customer Instruction Manual.docx

Page 33 of 68

4. SET LAMINATION FILM/MANUAL MODE (cont’d)

If the threading card and film do not emerge from the discharge within 5 seconds pull the threading back out

of the nip and repeat the threading process from step 6. If the machine is not threaded properly damage to

interior components will occur.

15. After most of the threading card and film web

emerge from the discharge lower the Lamination

Handle.

STOP! Do not go any further until the READY

light is on AND the machine is fully heated.

16. It is very important to run the machine in

“manual mode” (using the MOVE switch) and

observe the film as it exits the discharge. It

should be well laminated (clear) and free of

wrinkles. If wrinkles are observed adjust the

tension controller knobs slightly on the film

rolls. If the film is curled this could be an

indication that the tension of one of the film

rolls is tighter than the other. Film must exit

the machine flat, clear and free of wrinkles

before being put into automatic mode

(pressing the START button). If there is curl

during manual mode there may be curl during

automatic mode which will likely produce

errors and possibly damage interior

components the machine.

Содержание AL-MEISTER ALM3230





































































Результаты поиска

Содержание AL-MEISTER ALM3230

Отзывы:

Похожие инструкции для AL-MEISTER ALM3230

Бренды по названию

Популярные бренды

FUJIPLA AL-MEISTER ALM3230, Инструкция по эксплуатации

Результаты поиска

Содержание AL-MEISTER ALM3230

Отзывы:

Похожие инструкции для AL-MEISTER ALM3230

Бренды по названию

Популярные бренды