FUJIPLA AL-MEISTER ALM3230 Скачать руководство пользователя

Страница: 34 / 68

DryLam

A Trademark of Martin Yale Industries

251 Wedcor Avenue, Wabash, IN 46992

Brian Jennett- Tech-Line & Service Advisor/Manager

Phone: (260-569-7231)

www.DryLam.com

ALM3230 Customer Instruction Manual.docx

Page 34 of 68

4. SET LAMINATION FILM/MANUAL MODE (cont’d)

17. Adjustment of tension controllers

There are four (4) tension controllers- two for the lower film roll and two for the upper film roll. The purpose

of the tension controllers is to apply a resistance, or "drag" on the film rolls which forces the film lay flat on the

heat rollers and thereby eliminates creases and bubbles in the lamination.

It is recommended that the right side and left side controllers on each roll be adjusted with the same amount

of tension. The top pair of controllers versus the bottom pair of controllers may vary slightly only to eliminate

"curl" in the laminated piece. If the laminated piece curls upward loosen the two upper controllers and/or

tighten the two bottom controllers. If the exiting laminated piece curls downward, do the opposite and make

the lower controllers looser than the upper controllers.

18. Again, after the laminator has "warmed-up" and the READY light is on, use the manual MOVE switch to run

film (by itself, no paper) out of the laminator. Observe these samples for clarity and freedom from wrinkles.

When all of the bubbles, wrinkles and creases disappear from the lamination and the film is lying flat on the

heat rollers the machine is ready to be run in “automatic mode”. If lamination defects are not disappearing in

a reasonable amount of film footage (3 or 4 feet), slightly increase tension on the controllers (equally). See

Step 17.

Содержание AL-MEISTER ALM3230





































































Результаты поиска

Содержание AL-MEISTER ALM3230

Отзывы:

Похожие инструкции для AL-MEISTER ALM3230

Бренды по названию

Популярные бренды

FUJIPLA AL-MEISTER ALM3230, Инструкция по эксплуатации

Результаты поиска

Содержание AL-MEISTER ALM3230

Отзывы:

Похожие инструкции для AL-MEISTER ALM3230

Бренды по названию

Популярные бренды