manualshive.com logo in svg

Fuji Xerox ApeosPort-V C2276, Руководство администратора

Поделиться
Скачать
Fuji Xerox ApeosPort-V C2276 Скачать руководство пользователя страница 93

Replacing Consumables

93

M

a

int

e

na
nc
e

3

3

Hold the tabs on both sides of a new booklet 
staple cartridge, and insert it into the finisher 
until it clicks.

4

Do the same for the booklet staple cartridge on the other side.

5

Close the finisher side cover.

Note

•

If the cover is not closed completely, a message appears and the machine will remain paused.

Replacing Booklet Staple Cartridge (for C3 Finisher with Booklet Maker)

When the C3 Finisher with Booklet Maker (optional) is installed and the booklet staple 
cartridges need to be replaced, a message appears on the touch screen. When this message 
appears, replace the booklet staple cartridges with new ones.

* : The messages above are for the Booklet Staple Cartridge [R2]. For the Booklet Staple Cartridge [R3], [R3] is displayed.

Important •

The use of booklet staple cartridges not recommended by Fuji Xerox may degrade quality and 
performance. Use only booklet staple cartridges recommended by Fuji Xerox.

Note

•

If the booklet staple cartridge was not replaced properly, the message remains on the touch screen. 
Follow the procedure and replace the booklet staple cartridge again.

•

To order a booklet staple cartridge, contact our Customer Support Center.

1

Make sure that the machine is not operating, 
and open the finisher front door.

Message

Solution

The Booklet Staple cartridge [R2] is running out 
of staples. Please order a Booklet Staple 
Cartridge [R2].

Prepare new staples.

Note

•

Staples cannot be replaced yet.

The Booklet Staple Cartridge [R2] is out of 
staples or not fully inserted. Check the Staple 
Cartridge [R2].

Replace staples with new ones.

Содержание ApeosPort-V C2276
















































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды